This product is a 25% solids solution of Chlorinated Polyolefin 343-3 in Xylene. It has a 26-32 wt % chlorine content and a Gardner color value of 6-7. CP 343-3 has a good solvent tolerance for a wide range of solvents. The higher chlorine content than CP343-1 gives improved compatibility with co-resins. Recommended as stir-in additive to promote adhesion to PP-based substrates.

Eastman™ 1,4-Diisopropylbenzene is a chemical intermediate for the preparation of stabilizers, polymers, synthetic lubricants, hydroperoxides, and a variety of other products.

Eastman™ meta-DIPB (1,3-Diisopropylbenzene) is a chemical intermediate for the preparation of stabilizers, polymers, synthetic lubricants, hydroperoxides, and a variety of other products.

Eastman™ 1,3,5-Triisopropylbenzene is a clear, high-boiling, odorless liquid. It is a low-toxicity alkylaromatic solvent used in the formation of higher-boiling aromatic/water azeotropes.

Chlorinated Polyolefin 343-1 is supplied as a white powder and is soluble in both Toluene and Xylene. It has a 18-23 wt % chlorine content. This product is 100% solids and is supplied in powder form. Excellent adhesion to polypropylene based substrates. Also promotes adhesion to steel, galvanized steel, phosphated steel, wood and rigid PVC.

This product is a 50% solution of Chlorinated Polyolefin 343-3 in Xylene. It has a 26-32 wt % chlorine content and a Gardner color value of 11. CP 343-3 has a good solvent tolerance for a wide range of solvents. Higher chlorine content than CP343-1 gives improved compatibility with co-resins. Recommended as stir-in additive to promote adhesion to PP-based substrates.

This product is a 25% solids solution of Chlorinated Polyolefin 153-2 in Xylene. It has a 21-25 wt % chlorine content and a Gardner color value of 12-15. It is recommended as an adhesion-promoting primer for untreated polyethylene-based substrates.

This product is a 50% solids solution of Chlorinated Polyolefin 343-1 in Xylene. It has an 18-23 wt % chlorine content and a Gardner color value of 8. Excellent adhesion to polypropylene based substrates. Also promotes adhesion to steel, galvanized steel, phosphated steel, wood and rigid PVC.

This product is a 50% solids solution of Chlorinated Polyolefin 343-1 in Xylene. It has an 18-23 wt % chlorine content and a Gardner color value of 8. Excellent adhesion to polypropylene based substrates. Also promotes adhesion to steel, galvanized steel, phosphated steel, wood and rigid PVC.

This product is a 40% solids solution of Chlorinated Polyolefin 515-2 in Xylene and is a liquid at room temperature. CP 515-2 is compatible with a variety of resins. Recommended as stir-in additive to promote adhesion to PP and other difficult to coat substrates.

This product is a 40% solids solution of Chlorinated Polyolefin 515-2 in Aromatic 100 and is a liquid at room temperature. CP 515-2 is compatible with a variety of resins. Recommended as stir-in additive to promote adhesion to PP and other difficult to coat substrates.

This product is a 40% solids solution of Chlorinated Polyolefin 343-1 solids in Xylene. It has an 18-23 wt % chlorine content and a Gardner color value of 8. Excellent adhesion to polypropylene based substrates. Also promotes adhesion to steel, galvanised steel, phosphated steel, wood and rigid PVC.

CP 310W is a water dispersion of a chlorinated polyolefin. Oil in water type emulsion containing ammonia as a neutralizing amine. The faster evaporating ammonia makes it more useful in adhesion promoting primers that are air dried prior to application of a topcoat. Recommended for adhesion to untreated polypropylene-based substrates.

CP 349W is a water dispersion of a chlorinated polyolefin. Oil in water-type emulsion. It contains 5 wt % ethylene glycol, and has 2-amino-2-methyl-1-propanol as the neutralizing amine which makes it more compatible with other waterborne resins and more useful as an additive. Recommended for promoting adhesion to untreated polypropylene-based substrates.

CP 347W is a water dispersion of a chlorinated polyolefin. Oil in water-type emulsion. It contains 2-amino-2-methyl-1-propanol as the neutralizing amine which makes it more compatible with other waterborne resins and more useful as an additive. Recommended for promoting adhesion to untreated polypropylene-based substrates.

This product is a 40% solids solution of Chlorinated Polyolefin 515-2 in Toluene and is a liquid at room temperature. CP 515-2 is compatible with a variety of resins.

Eastman™ liquid ethylene is a highly flammable, colorless, nontoxic gas with a characteristic sweet odor and taste. Applications include refrigerant fluid for low temperatures, monomer for polyethylene and waxes, and a reactant.

Eastman™ n-Butanol is a four carbon straight chain oxo alcohol. It is a medium-boiling liquid that is useful as a chemical intermediate and as a solvent for ambient dry and baking coatings.

Eastman™ n-Propanol, a three-carbon straight chain oxo alcohol, is a medium-boiling, colorless liquid that is widely used in flexographic and other printing ink applications. It has a very mild odor, similar to that of ethanol and is completely soluble in water.

Eastman™ Acetaldehyde is a highly reactive, flammable, colorless liquid. It is miscible with water, ethyl alcohol, ethyl ether, acetone, benzene, gasoline, toluene, xylene, and acetic acid.

This eight-carbon branched chain oxo alcohol with a high boiling point and slow evaporation rate features excellent reactivity as a chemical intermediate. It serves as a chain terminator in synthesizing condensation polymers and as an intermediate for plasticizers.

Eastman™ Propionaldehyde is a colorless, flammable liquid used primarily as a chemical intermediate.

Eastman EB Solvent (Ethylene Glycol Monobutyl Ether) offers numerous benefits in coating, ink, and cleaner applications. It is an excellent solvent for many coatings resin types, including alkyd, phenolic, maleic, epoxy, and nitrocellulose resins. Its unique combination of properties enables the effective removal of contaminants when used in Industrial & Institutional and/or household cleaners.

Eastman™ Isobutanol is a medium-boiling, slow-evaporating, colorless liquid that is useful in organic synthesis, as a chemical intermediate, and as a solvent in coating applications.

Eastman™ Isobutyl Acetate is a medium-boiling solvent with a typical mild, fruity, ester odor. Its combination of good solvent activity, desirable evaporation rate, and pleasant odor enables it to be used in a wide range of coating applications.

Isobutyric Acid is a colorless, medium boiling liquid. Esters of isobutyric acid are used as solvents for various applications where desirable odors and flavor characteristics are important.

Eastman DB Solvent (Diethylene Glycol Monobutyl Ether) improves the flow-out and gloss of baking enamels, is an effective coalescent in both architectural and industrial maintenance formulations, can be used in printing inks to increase dry times, and provides excellent coupling ability for the effective removal of contaminants in Industrial & Institutional and/or household cleaners.

Eastman offers two nitrile-based products including Isobutyronitrile and n-Butyronitrile. These products are used in pharmaceutical, agricultural, and process solvent applications.

Eastman™ 2-Ethylhexaldehyde is an aldehyde product.

Eastman TMPD™ Glycol is used to formulate saturated polyester resins for liquid coatings and unsaturated polyester laminating resins sold into a wide variety of markets. It is available in cast solid form in drums or bulk molten form delivered in tank trucks.

Eastman NPG is the industry standard glycol component in high-quality polyester resins for industrial coatings and fiberglass-reinforced plastics applications. The platelet form is supplied in bags that exhibit excellent caking stability on storage.

Eastman Cellulose Acetate Butyrate CAB-531-1 is a cellulose ester with a higher butyryl level than CAB-381 series esters. It offers improved compatibility, and due to its flexibility, it requires lower plasticizer modification. When combined with thermoplastic acrylic resins, it produces tough, weather and mar resistant films.

Eastman Cellulose Acetate Propionate CAP-482-20 has similar characteristics to CAP-482-0.5, but with a higher viscosity. It is useful as a film former in inks, overprint varnishes, and nail lacquer topcoats.

Eastman Cellulose Acetate Butyrate CAB-381-0.1 is a cellulose ester with medium butyryl content and low viscosity. It was designed for use where low application viscosities at relatively high solids levels are needed. CAB-381-0.1 is used when lower viscosity for higher solids formulations and increased toughness with excellent surface hardness is desired. It is used in automotive basecoats for metallic flake control and is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate Butyrate CAB-381-0.5 is a cellulose ester with medium butyryl content and low viscosity. It was designed for use where low application viscosities at relatively high solids levels is needed. It is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate Butyrate CAB-381-2 is a cellulose ester with medium butyryl content and high viscosity. It offers a combination of solubility and compatibility, moisture resistance, excellent surface hardness, and good film strength. It is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate Butyrate CAB-381-20 is a cellulose ester with medium butyryl content, very high ASTM(A) viscosity, and great rheological modification. It offers a combination of solubility and compatibility, moisture resistance, excellent surface hardness and good film strength. It is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate Butyrate CAB-500-5 is a cellulose ester with high butyryl content, low hydroxyl content and medium viscosity. It produces a relatively soft, flexible film requiring little or no plasticizer in many applications and offers a wide range of solubility and compatibility. It is useful in leather coatings and as a flow control additive in polyurethanes.

Eastman Cellulose Acetate Butyrate CAB-551-0.2 is a cellulose ester with high butyryl content and relatively low molecular weight. Its good compatibility with various resin systems and its solubility in a wide variety of solvents makes it useful as an additive in numerous coating compositions, including high-solids and thermoset coatings, and as a modifier for UV-curing systems.

Eastman Cellulose Acetate CA-320S is a cellulose ester with a high hydroxyl content. It is supplied as pellets.

Eastman™ reagent-grade glacial acetic acid can be used in the semiconductor industry, in chemical laboratories or in other industrial applications where an exceptionally pure grade of glacial acetic acid is required.

Eastman Cellulose Acetate Propionate CAP-504-0.2 is a free-flowing powder with low odor, low color, and high hydroxyl content. It has a low viscosity (0.2 seconds) and an approximate propionyl content of 42.5 wt %. CAP-504-0.2 is compatible with many ink resins and solvents.

Eastman Cellulose Acetate CA-394-60LF is a very high-melting, low odor cellulose ester having limited solubility and compatibility. This multipurpose rheology enhancer, offers high strength and good resistance to ultraviolet light, heat, oils, and greases. It is useful in lacquers for glass, plastic, wire and release coatings.

Eastman Cellulose Acetate Butyrate (CAB-551-0.01) has many unique attributes that will serve useful across many different coating application areas. It has the lowest Tg (glass transition temperature) of the CAB portfolio.

Eastman Cellulose Acetate CA-398-30 is a high-viscosity, high molecular weight cellulose acetate supplied as fine, dry, free-flowing powder. Its relatively uniform particle size permits good plasticizer distribution during blending and it offers good physical properties for molded and extruded articles.

Eastman Cellulose Acetate Butyrate CAB-381-2BP grade ester is a slight modification of the standard CAB-381-2 and has a higher hydroxyl and acetyl content and lower butyryl content. The BP grade was designed primarily to meet the needs of European formulators.

Eastman Cellulose Acetate Butyrate CAB-381-20BP grade ester is a lower hydroxyl content version of the standard CAB-381-20 and has a lower viscosity. The BP grade was designed primarily to meet the needs of European formulators.

Eastman Cellulose Acetate Butyrate CAB-321-0.1 is a cellulose ester with a low butyryl content (32.5%) and low molecular weight. Designed for use in automotive basecoats, it is resistant to attack and resistant to redisolve by solvents typical in clearcoats. It has a viscosity of 0.10 sec and 0.38 poise. CAB-321-0.1 is supplied as a fine white powder.

Eastman EastaPure™ acetic acid has an extremely low metal content and is an excellent choice for use in etching solutions for semiconductor chips and other electronic applications.

Eastman™ DTBHQ is a white to tan, crystalline solid that is insoluble in water and caustic solutions. Eastman™ DTBHQ has a low vapor pressure and short induction periods in peroxide-catalyzed polymerizations.

Eastman™ MTBHQ (2-Tert-Butylhydroquinone) is a light tan solid used primarily as a polymerization inhibitor and industrial antioxidant. Its higher solubility and increased potency at higher temperatures combine to make it more useful than unsubstituted hydroquinone in many applications.

Eastman™ Poly TDP-2000 antioxidant is typically used as a secondary antioxidant along with phenolic primary antioxidants in plastics. Eastman™ Poly TDP-2000 shows excellent stability in high-temperature applications and functions well in the presence of UV light stabilizers and other additives.

Hydroquinone is a white, crystalline solid and is used as a good general-purpose inhibitor, stabilizer, antioxidant, and intermediate. This product is the Photographic Grade of Hydroquinone.

Antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life. Eastman Tenox™ 8 Food-Grade Antioxidant, Kosher is a formulation of Eastman Tenox™ BHT.

3-(N-Benzyl-N-ethylamino)acetanilide is a brown solid melting at 104° C that is used as a photographic chemical.

Eastman Tenox™ 20 food-grade antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Eastman Tenox™ 20A food-grade antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Hydroquinone has been formulated for many years into creams, lotions, and gels to produce effective skin-lightening products. Eastman™ Hydroquinone, USP Grade, meets or exceeds the requirements of the United States Pharmacopeia.

Eastman Tenox™ 21 food-grade antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Eastman Tenox™ antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Antioxidants stabilize various fats, oils, food, and cosmetics against oxidative deterioration, thus extending product shelf life.

Eastek™ 1100 polymer is a film forming polyester polymer supplied as an aqueous dispersion containing 33% polymer solids.

Eastek™ 1300 polymer dispersion, alcohol-free is a film forming polyester polymer. Aqueous dispersions of this polymer are characterized by low odor, good storage stability, and reducibility with water or water/alcohol mixtures.

Eastek™ 1200 polymer dispersion is a film forming polyester polymer supplied as an aqueous solution containing 2% n-propanol and 30% polymer solids.

Eastek™ 1000 polymer dispersion is a film forming polyester polymer supplied as an aqueous dispersion containing 30% polymer solids.

Eastek™ 1400 polymer dispersion is a 100% sulfopolyester. Aqueous dispersions of this polymer are characterized by low odor, good storage stability, and reducibility with water or water/alcohol mixtures.

DMT is a solid at room temperature and also available in bulk molten form. It is used with glycols to make polyester and in the synthesis of polyethylene terephthalate (PET) for fiber, film, container plastics, or specialty plastics.

Eastman™ DMCD is a low-melting, cycloaliphatic diester used for the synthesis of polyester resins, polyamides, alkyds, and plasticizers in a wide variety of coatings applications. It is also used in unsaturated polyester resin gel coats for fiberglass-reinforced plastics.

Eastman CHDM-D is a symmetrical, high molecular weight cycloaliphatic glycol used to make saturated and unsaturated polyester resins. It has also found use as a glycol modifier for resins containing Eastman NPG™ glycol. Good chemical, stain, humidity, and corrosion resistance is achieved when using CHDM-D in polyester-melamine baking enamels for appliance, general metal, and automotive coatings.

Eastman CHDM-D90 is a 90/10 weight % solution of CHDM-D in water. It is a liquid at room temperature for easier handling. This symmetrical, high molecular weight cycloaliphatic glycol is used to make saturated and unsaturated polyester resins. It is commonly used as a glycol modifier for resins containing Eastman NPG™ glycol. The 10 weight % water is removed during heating of the resin reaction mixture. Good chemical, stain, humidity, and corrosion resistance is achieved when using CHDM-D90 in polyester-melamine baking enamels for appliance, general metal, and automotive coatings. It delivers good hydrolytic stability to waterborne polyester resins.

Eastman™ Purified Terephthalic Acid (PTA) is a high-melting, white powder. It is used in making polyester resins for high-quality industrial coatings or unsaturated polyesters for the fiberglass-reinforced plastics industry with excellent performance characteristics.

<i>Ecdel™ 9967 elastomer meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Ecdel elastomers are plasticizer free copolyester elastomers (COPE) that offer clarity, toughness, flexibility, and chemical resistance for flexible packaging including medical and pharmaceutical applications. Ecdel 9967 may be processed on standard injection molding, extrusion blow molding, profile extrusion, extrusion coating, or film extrusion equipment. Ecdel elastomers are radiation, electron beam, ethylene oxide, and autoclave sterilization stable. Ecdel 9967's high inherent viscosity may be helpful where good melt strength is required (blown film or profile extrusion).

<i>Ecdel™ 9966 elastomer meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Ecdel elastomers are plasticizer free copolyester elastomers (COPE) that offer clarity, toughness, flexibility, and chemical resistance needed in a variety of flexible packaging including flexible medical and pharmaceutical packaging applications. Ecdel™ elastomers are radiation, electron beam, ethylene oxide, and autoclave sterilization stable. Ecdel 9966's medium inherent viscosity makes it a good general purpose elastomer. Ecdel 9966 may be injection molded or extruded.

Eastman AQ™ 38S polymer offers superior water resistance with the following characteristics: ultrafine dispersions, excellent film formation properties, water phase dispersion, emulsifier function for organic materials such as organic UV absorbers with no neutralization needed. Because of its low Tg, it forms flexible films on the skin; imparts a smooth feel to creams, lotions, and sprays; and adheres to the skin. It provides excellent water resistance in sunscreen products.

Eastman AQ™ 55S polymer is a water-dispersible sulfopolyester that has good film integrity when combined with other cosmetic ingredients. It is the preferred AQ polymer to improve water and smudge resistance of water-based makeup and mascaras, and in hairstyling products, it provides excellent hold under high-humidity conditions and tunable firmness. It has a Tg of about 55° C. The "S" indicates the product is supplied as solid pellets.

Eastman AQ™ Ultra polymer is a sulfopolyester that disperses directly in a mixture of ethanol and water at room temperature or in warm water without the assistance of surfactants or other additives. It is designed specifically for use as a hair fixative in low-VOC (<55%) hair spray. AQ 48 can also be used to formulate clear styling gels.

Tenite™ Acetates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Acetate 105-33 is heat stabilized and has a plasticizer level of 33%.

Tenite™ Acetates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Acetate 105-28 is heat stabilized and has a plasticizer level of 28%.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 264-13 has a plasticizer level of 13%.

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 264-10 has a plasticizer level of 10%.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 285-10 has a 10% plasticizer level and an odor mask.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 485-16 has a 16% plasticizer level, an odor mask, and ultraviolet inhibitor.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 485-10 has a 10% plasticizer level, an odor mask, and ultraviolet inhibitor.

Tenite™ Cellulose Acetate Butyrate 485-13 contains an odor mask and an ultra-violet inhibitor (UVI). It has a plasticizer level of 13%.

Tenite™ Cellulose Acetate Butyrate 485-16 contains an odor mask and an ultra-violet inhibitor (UVI). It has a plasticizer level of 13%.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 530-05 has a 5% plasticizer level and an odor mask.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 530-10 has a 10% plasticizer level and an odor mask.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 575-10 has a 10% plasticizer level and an odor mask.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 576-10 has a 10% plasticizer level and an odor mask.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 307-15 has a 15% plasticizer level.

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel. The mechanical properties if Tenite™ cellulosic plastics differ with plasticizer levels.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary depending on the plasticizer level. This Tenite™ Propionate 350-14 has a natural, transparent color and a 14% plasticizer level.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 358-18 has a plasticizer level of 18%.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary depending on the plasticizer level. Tenite™ Propionate 360-12 is clear and has a 12% plasticizer level.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR> Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel. This Tenite™ Propionate 360-07 is clear, transparent, and has a plasticizer level of 7%. This product does not contain a mold release.

Tenite™ Cellulosic Acetate Propionate 360-14 has a plasticizer level of 14%.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary depending on the plasticizer level. This Tenite™ Propionate 360-12 is clear, resistant to high temperatures, and has a 12% plasticizer level.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary depending on the plasticizer level.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 371-09 has a 9% plasticizer level and mold release.

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel. Tenite™ cellulosic plastics are available in natural, clear, selected ambers or smoke transparents and black translucent. Color concentrates are available in let-down ratios from 10:1 to 40:1. Tenite™ Cellulose Acetate Propionate 371-12 contains a mold release and has a plasticizer level of 12%.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 375-12 has a plasticizer level of 12%.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 376-12 has a 12% plasticizer level and an ultraviolet inhibitor.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 377-12 has a plasticizer level of 12%.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary in each product depending on the plasticizer level. Tenite™ Propionate 380-10 has a 10% plasticizer level and is resistant to high temperatures.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary in each product depending on the plasticizer level. Tenite™ Propionate 380-15 has a 15% plasticizer level and is resistant to high processing temperatures.

Tenite™ Cellulose Acetate Propionate 380-18 has a plasticizer level of 18%. It is resistant to high processing temperatures.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 383-09 has a 9% plasticizer level, high temperature resistance, and mold release.

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel. Tenite™ Cellulose Acetate Propionate 383-10 contains a mold release and has a plasticizer level of 10%.

Tenite™ Cellulose Acetate Propionate 383-11 contains a mold release and has a plasticizer level of 11%.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Propionate 384-16 has a 16% plasticizer level, high temperature resistance, and an ultraviolet inhibitor.

Eastar™ Copolyesters are brilliantly clear polymers that have excellent impact strength, chemical resistance, dimensional stability, and low shrinkage rates. DN003 contains a mold release.

Eastar™ DN004 copolyesters are brilliantly clear polymers and our toughest materials for the cosmetics and personal care packaging applications. It's very shatter resistant and offers excellent chemical resistance. DN004 contains a mold release.

Amietol M11 (MMEA) is a clear hygroscopic liquid with an amine-like odor.

Amietol M12 (MDEA) is a clear hygroscopic liquid with an amine-like odor. The freshly distilled product is colorless, but prolonged storage may cause a yellowish discoloration.

DMAPA is a clear colorless liquid, free of suspended matter. DMAPA is completely miscible with water, alcohols, esters and ketones.

Dimethylformamide Peptide Grade is a clear, colorless, hygroscopic liquid.

<b>Metam potassium is a “Restricted Use Pesticide” in the US.</b><br>Soil disinfectant for controlling nematodes, soil diseases, weeds and germinating weed seeds. The product works by fumigation. It is applied prior to seeding or planting, creating a favorable biotope that promotes healthy crop growth.

Diethylaminoethanol (DEAE) is a clear liquid. It is used as a neutralizing amine for boiler water, coatings, etc.

Monoethylamine (MEA) is available as an anhydrous liquid. MEA has an ammonia-like odor and is miscible with water, alcohol and ether.

Monoethylamine 70% (MEA-70%) is an aqueous colorless solution. MEA-70% has an ammonia-like odor.

Diethylamine (DEA) is available as an anhydrous colorless liquid. DEA has an ammonia-like odor.

Triethylamine (TEA) is a colorless liquid with an ammonia-like odor.

Mono-n-Propylamine (MNPA) is a clear colorless liquid with an ammonia-like odor. MNPA is miscible with water, alcohol and ether.

Di-n-Propylamine (DNPA) is a colorless liquid with an ammonia-like odor. DNPA is moderately soluble in water.

Di-n-Propylamine (DNPA) is a colorless liquid with an ammonia-like odor. DNPA is moderately soluble in water.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ copolyester MB002 is a resin specifically developed for extrusion blow molding containers in medical applications where aesthetics such as high clarity and gloss, coupled with high toughness, and chemical resistance, are desirable.

Eastar™ EB062 copolyester is a resin specifically designed for extrusion blow-molded bottles and jars for use in food and beverage and home care applications. Its high drop strength makes it particularly well suited for containers that hold heavier contents, including liquids and dense solids.

Eastar™ Polyester EN052 is a thermoplastic condensation homopolymer produced by a continuous melt-phase polymerization process followed by a solid-state polymerization process.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><br> Eastar™ Polyester MN052 does not contain a mold release. It has a relatively high flex modulus and yield strength. This product has high flow characteristics.

Eastman™ 1,3,5-TIPB (1,3,5-Triisopropylbenzene), 97% is a clear, high-boiling, odorless liquid.

Eastman Cadence™ GS5 is the top-of-the-line copolyester resin for calendered film applications including decorative laminates, general purpose packaging, transaction and identification cards, and protective films. It has superior processing ease and speed compared to Cadence™ GS2 and GS3.

Eastman Optifilm™ enhancer 300 is a low odor, coalescent that is safe, efficient and nonyellowing. Used in a variety of latex types, it is also compatible with solvent borne resins, improving the rheology, flexibility, and adhesion of coatings based on these resins. Eastman Optifilm™ enhancer 300 is VOC-exempt under the European Union Decopaint directive and Solvent Emissions Directive, the Australian Paint Approval Scheme.<br> Useful for preparing low viscosity weatherable PVC coil coatings. Coalescing aid with low volatility and excellent application properties. Excellent properties with associative thickeners.

Eastman Optifilm™ enhancer 400 is a low odor coalescent that is compatible with a variety of latex types, and it does not significantly contribute to the VOC content of paints.

Eastar™ EN076 copolyester is a clear copolyester used in a variety of packaging and consumer product applications, including food and beverage packaging, general purpose packaging, flexible film packaging, and consumer products

Eastman™ Cellulose Acetate (CA-320S NF/EP) is a low acetyl content of CA. CA-320S NF/EP is commonly used in osmotic drug delivery and taste-masking.

Eastman Embrace™ High Yield is combined with Eastman Embrace™ LV copolyester to create a white opaque microvoided shrinkable film. Embrace High Yield has a density below 1.0 g/cc with a high ultimate shrinkage up to 70%.

Release additives are required to calendar Eastman Cadence™ materials.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ Copolyester MN006 Natural is a brilliantly clear polymer having excellent impact strength, chemical resistance, and low shrinkage rates. Eastar™ Copolyester MN006 Natural contains a mold release. This polymer is the toughest of the Eastar™ family of products. Additional outstanding features are chemical resistance and excellent color and property retention following gamma and e-beam sterilization.

Eastman™ n-Propyl Propionate is a non-HAP, medium evaporating, urethane grade solvent with good activity for most coating resins.

Eastar™ DN114 contains an ultraviolet light inhibitor and a mold release.</p>

Eastman TXIB™ formulation additive is the lowest viscosity additive available to the flexible PVC industry, making this material particularly suitable for PVC plastisols and often allows adding additional fillers to the plastisol, resulting in a cost savings.

Tritan™ Renew VX351HF-50 is an amorphous copolyester with excellent clarity and impact resistance.

Eastman Acitra^TM LH2 NC is a buffered, liquid product to preserve feedstuffs from harmful microorganisms.

Tritan™ Renew copolyester EX401-25, specifically developed for the Infant Care market, is an amorphous copolyester with excellent appearance and clarity.

Eastman Tritan MXF321 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability. Eastman Tritan MXF321 contains a mold release derived from vegetable based sources.

Eastman Tritan MXF321 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability. Eastman Tritan MXF321 contains a mold release derived from vegetable based sources.

Eastman Tritan™ Renew TX1501HF-25 is a high flow grade of Eastman Tritan. Tritan Renew TX1501HF-25 has viscosity reductions of 40-50% relative to Eastman Tritan copolyester TX1001, as well as Tritan Renew TX1001-25 and TX1001-50. Eastman Tritan Renew TX1501HF-25 contains a mold release derived from vegetable based sources. Other outstanding features include good toughness, hydrolytic stability, and heat and chemical resistance. Tritan Renew TX1501HF-25 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. Tritan Renew TX1501HF-25 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman Tritan™ Renew TX1000-25 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This next generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Tritan™ Renew TX1000-25 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman TREVA™ Renew engineering bioplastic TR6021-71 Natural is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA™ Renew engineering Bboplastic OP6026-71 Clear is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact. Renew polymers enable a brand to reduce consumption of fossil feedstock-based plastics, achieve sustainability targets without compromise, and be a fast mover in a growing market for sustainable consumer products.

Eastman TREVA™ Renew engineering bioplastic GC6021 Natural is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA™ Renew engineering bioplastic OP6026-71 Natural is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA™ Renew engineering bioplastic GC6011-75 Natural is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA™ Renew engineering bioplastic TR6021-71 Natural is a cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA Renew Engineering Bioplastic TR6021-71 Clear is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman Tritan™ Renew TX1000-50 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new-generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Combined with Eastman Tritan's outstanding chemical resistance and hydrolytic stability, these features give molded products enhanced durability in the dishwasher environment, which can expose products to high heat, humidity and aggressive cleaning detergents. Tritan Renew TX1000-50 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. Tritan Renew TX1000-50 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman Tritan™ Renew TX1001-50 is an amorphous copolyester with excellent appearance and clarity. Tritan Renew TX1001-50 contains a mold release derived from vegetable based sources. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new-generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Combined with Tritan's outstanding chemical resistance and hydrolytic stability, these features give molded products enhanced durability in the dishwasher environment, which can expose products to high heat, humidity and aggressive cleaning detergents. Tritan Renew TX1001-50 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. Tritan Renew TX1001-50 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman Tritan MXF421HF copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF421HF has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF421HF has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability to fill complex parts. Tritan MXF421HF contains a mold release derived from vegetable-based sources.

Eastman Tritan MXF321 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability. Eastman Tritan MXF321 contains a mold release derived from vegetable based sources.

Eastman Tritan™ MXF421 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF421 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF421 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability to fill complex parts. Tritan MXF421 contains a mold release derived from vegetable-based sources.

Eastman™ Stabilizer TMR is used in total mixed ration (TMR) for cattle to prevent heating due to microbial growth and to prevent nutrient losses.

Eastman TREVA™ TR6011 Natural is a cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman Cristal™ Renew copolyester 400-50 is a high flow product. It is designed and engineered specifically for cosmetics packaging applications.

Eastman Cristal™ Renew 401-50 copolyester is a high flow product that contains mold release for ease of ejection. It is designed and engineered specifically for cosmetics packaging applications.

Eastar™ Renew copolyester AN014-30 Natural is a high flow product that contains a mold release.

Eastar™ Renew AN004-30 Natural copolyester contains a mold release. It has an excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. Its processability coupled with its outstanding chemical resistance makes it well suited for thick-wall applications.

Eastman Cristal™ Renew copolyester AN001-30 Natural has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities.

Eastman Cristal™ Renew copolyester CN015-25 Natural is a high flow product that contains a mold release to provide ease of demolding.

Eastman Eastar™ Renew BR003-30 copolyester is a brilliantly clear copolyester for toothbrushes specifically designed for brands and manufacturers who demand a more sustainable plastic material. Eastar™ Renew BR003-30 copolyester is identical in clarity, resistance to toothpaste and mouthwash, and in processing ease to Eastar™ BR003, which oral care brands around the world have come to count on for their simple and complex toothbrush designs.

Eastman Tritan™ Renew TX2001-50 is an amorphous copolyester with excellent appearance and clarity. Tritan Renew TX2001-50 contains a mold release derived from vegetable based sources. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new-generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Tritan Renew TX2001-50 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman Tritan™ Renew TX1501HF-50 is a high flow grade of Eastman Tritan. Tritan Renew TX1501HF-50 has viscosity reductions of 40-50% relative to Eastman Tritan copolyester TX1001, as well as Tritan Renew TX1001-25 and TX1001-50. Tritan Renew TX1501HF-50 contains a mold release derived from vegetable based sources. Other outstanding features include good toughness, hydrolytic stability, and heat and chemical resistance. Tritan Renew TX1501HF-50 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. Tritan Renew TX1501HF-50 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastar™ Renew GN071-30 copolyester is a sustainable, clear copolyester used in a variety of packaging and consumer product applications, including food and beverage packaging, general-purpose packaging, flexible film packaging, and consumer products.

Eastar™ Renew EN076-30 copolyester is a sustainable, clear copolyester used in a variety of packaging and consumer product applications, including food & beverage packaging, general purpose packaging, flexible film packaging, and consumer products. It is fully compatible with the resin identification code 1 (RIC1) recycle stream. Eastar™ Renew EN076-30 copolyester enables fast-moving consumer goods brand owners to achieve recyclable products and packaging, reduce consumption of fossil-based resources, and replace materials of concern without sacrificing aesthetics or quality.

Eastman™ Formic Acid 99 Feed is a liquid preservative to protect feeding stuffs against deterioration caused by a broad spectrum of micro-organisms.

Eastman BioSustane SAIB NF pharmaceutical excipient is a high viscosity liquid depot for extended drug delivery in enteral, parenteral, and topical applications.

EASTMAN RP100 Performance Additive is an extremely low odor, low emission and multi-functional product for broad sport surface applications. It is compatible with a wide variety of binders and formulations to provide superior viscosity reduction. It enables application easiness of variable sport surface formulas while providing better defoaming,levelling and a solution to resolve low temperature application constraints. It is capable of improving sport surface mechanical performance while achieving good balance between elasticity and strength.

Eastman Cristal™ copolyester EN067 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging with a combination of good color and high clarity for molded parts with an RIC1 resin. This product is suitable for thinner-walled molded parts for the cosmetics and personal care market.

Eastman Tritan™ Renew VX401-50 is an amorphous copolyester with excellent clarity and impact resistance. The outstanding chemical resistance, hydrolytic stability, and ease of processing make Tritan Renew VX401-50 an ideal candidate for a broad spectrum of optical applications.

Eastman Cristal™ EN076 copolyester is recommended for a variety of applications including thick-walled containers that are prevalent in the cosmetics and personal care markets. This copolyester offers good processability with the benefits of glass such as high clarity, brightness, and good color.

Eastman Cristal™ EB062 copolyester is a resin specifically developed for extrusion-blown bottles where aesthetics such as high clarity and gloss, coupled with design flexibility, drive demand particularly in packaging for cosmetics and personal care. Compared to commonly used materials, Cristal EB062 runs on most standard processing equipment. Extremely high melt strength makes the resin an excellent choice when manufacturing bottles. This product offers improved toughness, melt strength, chemical resistance, excellent color, and clarity in thick-walled applications.

Eastman Propcorn Feed LP3 NC is a non-corrosive propionic acid-based liquid product for aerobic preservation against molds in feedstuffs.

Eastman Acitra^TM LG1 has a preservative effect and prevents the growth of harmful bacteria in the feed and improves the quality and shelf life.

Eastman Acitra LH1 preserves compound feeds and raw materials and prevents recontamination with microorganisms.

Eastman Propcorn Feed LP2 NC is a non-corrosive propionic acid-based liquid product for aerobic preservation against molds in feedstuffs.

Eastman Advantex(TM) AR is a clear to light yellow liquid with an amine-like odor. The freshly distilled product is colorless, but prolonged storage may cause a yellowish discoloration.

Cristal™ Renew copolyester 400-30 is a high flow product. It is designed and engineered specifically for cosmetics packaging applications.

Eastman Cristal™ Renew copolyester 401-30 Natural is a high flow product that contains mold release for ease of ejection. It is designed and engineered specifically for cosmetics packaging applications.

Eastman Cristal™ Renew EB062-50 copolyester is a resin specifically developed for extrusion blown bottles where aesthetics such as high clarity and gloss, coupled with design flexibility, drive demand particularly in packaging for cosmetics and personal care. Compared to commonly used materials, Cristal EB062 runs on most standard processing equipment. Extremely high melt strength makes the resin an excellent choice when manufacturing bottles. This product offers improved toughness, melt strength, chemical resistance, excellent color, and clarity in thick-walled applications.

Eastman Cristal™ Renew copolyester EN067-30 is a copolyester designed to be fully compatible with the PET recycling stream.

Cristal™ Renew copolyester EN067-50 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging with a combination of good color and high clarity for molded parts with an RIC1 resin.

Eastman Acitra^TM SG1 prevents the feed against deterioration by micro-organisms and improves the quality and shelf-life of the feed.

Eastman Acitra^TM SG2 prevents the growth of harmful bacteria in the feed and improves the quality and shelf life.

Eastman Acitra^TM Plus SG3 prevents the feed against deterioration by microorganisms and improves the quality and shelf life of the feed.

Eastman Acitra^TM SH1 preserves compound feeds and raw materials and prevents recontamination micro-organisms.

Eastman Acitra LH3 Na is a buffered liquid blend, especially developed for grain treatment, for storage times up to 12 months.

Eastman Acitra^TM LH2 Na is a buffered, liquid product to preserve feedstuffs from harmful microorganisms.

Eastman Acitra^TM LG2 Na has a preservative effect, prevents the growth of harmful bacteria in the feed and improves the quality and shelf life.

Eastman Acitra^TM LG5 Na is a buffered, liquid product to control bacteria especially in fur animal feeds and slaughterhouse by-products.

Eastman Acitra^TM LF20 Na is a liquid preservative for controlling harmful microorganisms in feedstuffs acting against a broad spectrum of microorganisms.

Eastman Acitra^TM LG5 Na is a buffered, liquid product to control bacteria especially in fur animal feeds and slaughterhouse by-products.

Eastman Protaq^TM LL2 is a complementary feed to be used via water for drinking for poultry, pigs and rabbits.

Eastar™ BR003 copolyester contains an additive that provides optimum molding efficiency. It has excellent appearance and is nearly water clear. With superior chemical resistance, it maintains its physical properties and appearance when exposed to aromatic oils. BR003 is specifically formulated to provide the optimal combination of chemical resistance, bristle retention, strength, stiffness, processability, clarity, colorability, and feel for toothbrushes. It also offers greater design flexibility and can work for virtually any toothbrush configuration; as a result, brands can offer unique models that are tough to replicate—and launch them quicker. With BR003, molders can also consolidate resins versus having single resins for single designs.

Eastman™ C-A-P enteric coating material is a pH-sensitive cellulose derivative designed for coating pharmaceutical tablets, capsules or granules. It may also be used as a matrix material in solid dose forms. It will withstand prolonged contact with acidic gastric fluids.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastman Provista™ Copolymer MP002 is a resin specifically developed for extrusion into profiles for medical applications where aesthetics such as high clarity and gloss, coupled with design flexibility and enhanced toughness, drive demand.

Eastman Provista™ Copolymer ST is a resin specifically developed for profile extrusion where high clarity and gloss, toughness, and processability are critical.

MCHM is a co-product that is used as an industrial chemical in coal floatation.

Propionic Anhydride is a colorless liquid having a pungent odor and high boiling point. It is soluble in alcohol, ether, chloroform, and alkalies, but decomposes in water. This product is the Kosher grade offered by Eastman.

Isobutyric Anhydride, Kosher is a liquid with a boiling range of 180-187°C used primarily when a kosher product is required in chemical processing and as a chemical intermediate.

Propionic Acid, Food Grade, Kosher is a food ingredient used in applications where a kosher food grade product is required. It is often used as an antimicrobial or flavoring agent.

n-Butyric Anhydride is a water-white liquid that hydrolyzes to butyric acid. It has a minimum assay of 98%. This kosher product is for use in food as a reactant only.

HPHP, Molten is a difunctional ester-glycol used for manufacturing polyester resins for the powder, coil, and automotive coatings market. The bulk molten form of HPHP is shipped in tank trucks requiring a heated tank for storage.

Aqueous dispersions of Eastman AQ™ 65S polymer provide excellent water resistance, alcohol resistance, fast drying rates, low odor, and a consistently low coefficient of friction.

Eastman 168 non-phthalate plasticizer is an excellent general purpose non-orthophtalate plasticizer with performance equal or better than most <i>ortho</i>-phthalate plasticizers. It offers good performance properties, excellent low temperature flexibility, resistance to extraction by soapy water, and excellent non-migration properties.

4-ADPA is used as a chemical intermediate.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 65% dilution strength.

Eastar™ AN004 copolyester contains a mold release. It has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. Its processability coupled with its outstanding chemical resistance makes it well suited for thick-wall applications.

Eastman EastaPure™ PM acetate is being offered for photoresist formulations. It is a slow evaporating solvent with both ether and ester functional groups.

Eastman™ C-A-P enteric coating material is a pH-sensitive cellulose derivative designed for coating pharmaceutical tablets, capsules or granules. It may also be used as a matrix material in solid dose forms and will withstand prolonged contact with acidic gastric fluids.

Eastman™ MPK, UHP (Ultra High Purity) is a medium-evaporating, urethane grade, highly active solvent for most synthetic resins. It is ideal as a letdown solvent for high solids, air-dry resins used in low VOC alkyd and polyester/urethane coatings. It is used in gravure printing inks and also provides excellent performance for a wide range of cleaning and surface preparation applications for the transportation industry.

Eastar™ GN007 Copolyester is a water-clear glycol modified polyethylene terephthalate (PET) with an added mold release. This material offers an excellent combination of clarity, toughness, and melt strength that makes it useful for a variety of processing techniques and end-use applications.

Tenite™ Cellulose Acetate Butyrate 285-20 has a plasticizer level of 20% and contains an odor mask.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 565-16 has a 16% plasticizer level and an odor mask.

Eastman Spectar UV™ copolyester is a versatile copolyester that extrudes into plastic sheet that is sparkling clear, tough, chemically resistant, odor free, easy to work with, and affordable. It is easy to fabricate, allowing greater design freedom. It can be laser cut, routed, welded, drilled, die-punched, bent hot or cold, or joined by screws, rivets, or bolts.

Eastman Sustane™ SAIB ET-10 Food Grade, Kosher is primarily used as a weighting agent in beverages. It provides a pourable liquid that can be added directly to flavoring oil without heating.

Tenite™ Acetates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Acetate 105-27 is heat stabilized and has a plasticizer level of 27%.

Tenite™ Butyrates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. Tenite™ Butyrate 285-18 has an 18% plasticizer level and odor mask.

Tenite cellulosic plastics are noted for their excellent balance of properties including toughness, hardness, strength, surface gloss, clarity, and a warm feel.

Eastar™ GN071 copolyester is a clear copolyester used in a variety of packaging and consumer product applications, including food and beverage packaging, general-purpose packaging, flexible film packaging, and consumer products.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary depending on the plasticizer level. This Tenite™ Propionate 360-16 has a natural, transparent color and a 16% plasticizer level.

Eastman™ Ethyl Acetate, Urethane Grade is a low-boiling, fast-evaporating solvent with a mild, pleasant odor. It is widely used in formulating printing inks, adhesives, and lacquers. Ethyl acetate is miscible with most organic solvents and can be used in cleaner blends fo the removal of oils, grease, and soils.

Eastman EastaPure™ n-Butyl Acetate solvent is offered for negative and positive photoresist formulations and is used to make semiconductor chips.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ copolyester MN210, Natural is a brilliantly clear polymer with good impact strength, chemical resistance, dimensional stability, and low shrinkage rates. The slower rate of crystallization of this material makes it excellent for use in hot runner systems with valve or thermal gates.

Acetic Anhydride is manufactured by Eastman and supplied in various grades. This product is the reagent grade and is available in tank trucks, tank cars, and 55-gallon drums.

Eastman EEH solvent (Ethylene Glycol 2-Ethylhexyl Ether) has long been used in performance specialty coatings applications. It offers an excellent balance of performance properties when used as a coalescent in architectural and industrial maintenance coatings.

Eastman™ Methyl Acetate - High Purity is an active, urethane grade, fast-evaporating, mild odor solvent for a broad range of coating and ink resins. It is useful in polyurethane coatings and in applications where fast solvent release and quick dry-to-touch times are required. Methyl acetate, HP is a VOC-exempt, non-HAP, non-ODS, readily biodegradable solvent that can be used in blends to develop environmentally friendly cleaners.

Eastman™ Ethyl Acetate, NF/EP is a colorless, fragrant, low-boiling solvent. As a bulk pharmaceutical excipient, Ethyl Acetate, NF/EP meets the National Formulary (NF) and European Pharmacopoeia (EP) monograph specifications.

Eastman™ Ethyl Acetate, Food Grade is a colorless, fragrant, low-boiling solvent. This grade of ethyl acetate meets the monograph requirements for Ethyl Acetate, Food Grade, as set forth in the Food Chemicals Codex (FCC) and supplements. It is manufactured, processed, packed and held under appropriate Good Manufacturing Practices for use as a food chemical.

Eastman™ Ethyl Acetate, Food Grade, Kosher is a colorless, fragrant solvent. This grade of ethyl acetate meets the monograph requirements for Ethyl Acetate, Food Grade Kosher, as set forth in the Food Chemical Codex (FCC) and supplements. It is manufactured, processed, packed and held under appropriate Good Manufacturing Practices for use as a food chemical. In addition, this grade of ethyl acetate is produced under rabbinical supervision and meets the requirements for Kosher and Pareve, including Passover.

Eastman™ Ethyl Acetate, NF/EP, Kosher is a colorless, fragrant, low-boiling solvent. As a bulk pharmaceutical excipient, Ethyl Acetate, NF/EP, Kosher grade meets the National Formulary (NF) and European Pharmacopoeia (EP) monograph specifications and is a kosher product.

Eastman EastaPure™ Ethyl Acetate solvent is a viscosity reducer for resins used in photoresist formulations.

Eastman™ n-Butyl Propionate is a non-HAP, slow-evaporating, and urethane grade solvent with good solvent activity for most coating resins. It provides low volatility to coatings formulations.

Eastman Provista™ copolymer is a resin specifically developed for extrusion into profiles where aesthetics like high clarity and gloss, coupled with design flexibility drive demand.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ Copolyester MN211, Natural contains a mold release for improved ejection. It is a brilliantly clear polymer with good impact strength, chemical resistance, dimensional stability, and low shrinkage rates. The slower rate of crystallization of this material makes it excellent for use in hot runner systems with valve or thermal gates.

HPHP Glycol Nuggets is a difunctional ester-glycol used for manufacturing polyester resins for the powder, coil, and automotive coatings market. The nugget form of HPHP is shipped in bags that have good resistance to caking.

Eastman Tenox™ TBHQ food-grade antioxidant finds use in stabilizing oils, fats, foods, and cosmetics against oxidative deterioration and is the most effective antioxidant for highly unsaturated vegetable oils and many edible animal fats.

DuraStar™ Polymer DS2010 Natural polymer has excellent appearance and is nearly water-clear. Its most outstanding features are toughness, chemical resistance, and excellent processing characteristics. Easy to process, it flows readily and fills intricate molds.

DuraStar™ Polymer DS1010 Natural polymer contains a mold release. It has excellent appearance and clarity. Its most outstanding features are chemical resistance and excellent processing characteristics. In addition, it flows readily, fills intricate molds, and is well suited for thick-wall applications.

Eastman Spectar Frost™ copolyester has a matte finish with outstanding durability and toughness that enables displays and fixtures to use thinner gauge sheet than other common materials. Eastman Spectar Frost™ retains its matte finish when thermoformed, hot bent and after other fabrication processes.

Eastman Sustane™ SAIB MCT is a weighting agent designed for customers needing improved handling traits, enhanced cloud properties, and taste neutrality in beverages. Due to low viscosity, it can be added at common operating temperatures and conditions. The INCI (cosmetic ingredient) name for Eastman Sustane™ SAIB MCT is Sucrose Acetate Isobutyrate (and) Caprylic/Capric Triglyceride.

Eastman EastaPure™ MPK solvent can be utilized in a variety of specialty cleaning operations.

Provista™ UVI is a Provista™ copolymer with an indoor/outdoor UV package added to prevent yellowing caused by light. Provista™ copolymer is a resin specifically developed for extrusion into profiles where aesthetics like high clarity and gloss, coupled with design flexibility drive demand.

Eastman Provista™ UVO is a copolymer with an indoor/outdoor UV package added to prevent yellowing caused by light. Provista™ copolymer is a resin specifically developed for extrusion into profiles where aesthetics like high clarity and gloss, coupled with design flexibility drive demand.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>DuraStar™ Copolyester MN611 contains a mold release. It has excellent appearance and is nearly water-clear. Benefits include toughness, chemical resistance, and excellent processing characteristics.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ Copolyester MN200 is an amorphous copolyester with excellent flow characteristics as well as radiation resistance and chemical resistance.

Eastman Cadence™ GS3 is a clear copolyester resin specifically for calendered film applications including decorative laminates, general purpose packaging, transaction and identification cards, and protective films. It has enhanced processing ease and higher melt strength compared to Cadence™ GS2.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>DuraStar™ Copolyester MN621 contains a mold release to improve ejection. It has excellent appearance and is nearly water-clear. This resin is the toughest of the Durastar™ family of products.

DuraStar™ Polymer DS1110UVI Natural polymer contains an ultraviolet light stabilization package. It is recommended for indoor applications requiring enhanced color stability upon extended exposure to fluorescent light.

DuraStar™ Polymer DS2110UVI Natural polymer contains an ultraviolet light stabilization package. It is recommended for indoor applications requiring enhanced color stability upon extended exposure to fluorescent light..

<i>Eastar™ 6763 copolyester meets ISO 10993 and/or USP Class VI biocompatibility requirement; Food Contact Status compliant</i><br> Eastar 6763 is a clear, amorphous material that can be molded and extruded with ease. Its excellent performance properties include clarity, toughness, good melt strength, no dusting, no stress whitening, good heat sealability, easy cutting and thermoforming. Eastar 6763 may be colored using color concentrates, dry colors, or liquid colorants. Eastar 6763 can be safely sterilized with proper ethylene oxide, radiation, or electron beam methods without property loss or color shift. It is well suited for medical packaging.

Tenite™ Propionates are noted for their excellent balance of mechanical properties that vary from product to product depending on the plasticizer level. This Tenite™ Propionate 307-18 is clear and an 18% plasticizer level.

Eastar™ GN119 Copolyester is a low-I.V. PETG, for sale only in Asia as a high-flow formulation.

Release additives are required to calendar Eastman Cadence™ materials.

Eastman AP 550-1 (25% in Xylene) is a nonchlorinated polyolefin for improved coating adhesion on TPO and polypropelene-based substrates. It has excellent humidity & gasoline resistance particularly under 1K systems. It allows the formulation of melamine-cured systems with excellent performance properties previously only available in 2K systems.

Eastman™ Chlorinated Polyolefin 730-1 is designed to be the active component in adhesion promoter primers used to ensure adhesion of color coats and topcoats to polypropylene (PP) and thermoplastic olefin (TPO) plastics.

DuraStar™ Polymer DS1900HF Natural polymer is a high flow grade of DuraStar™. Outstanding features of DuraStar™ are easily maintained such as excellent appearance and clarity, good physical properties, chemical resistance, and easy processing. This high flow product is especially suited for those applications utilizing thin-walled intricate tools.

Eastar™ AN011 copolyester is a high flow product. Eastar™ AN011 flow lengths are increased 20-40% relative to Eastar™ AN001 as shown by spiral flow testing. It is one of our premier material for the cosmetics and personal care packaging market. Other outstanding features of Eastar™ are easily maintained such as excellent appearance and clarity, good physical properties, chemical resistance, and easy processing. This high flow product is especially suited for those applications utilizing thin-walled intricate tools. Eastar™ AN011 is approved for food contact.

DuraStar™ Copolyester MN630 does not contain a mold release. It has excellent appearance and is nearly water-clear. Its most outstanding feature is its high flow characteristic, with the ability to fill intricate tooling. It is easy to process with minimal drying time and has good toughness and chemical resistance.

Eastar™ AN014 copolyester is a high flow product that contains a mold release. Other outstanding features of Eastar™ are easily maintained such as excellent appearance and clarity, good physical properties, chemical resistance, and easy processing. Eastar™ AN014 is approved for food contact. Eastar™ AN014 flow lengths are increased 20-40% relative to Eastar™ AN004 as shown by spiral flow testing. This high flow product is especially suited for those applications utilizing thin-walled intricate tools. Under existing United States Food and Drug Administration (FDA) regulations, Eastar™ AN014 may be used in food contact articles which comply with the specifications and conditions of use in 21 CFR 177.1240.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>DuraStar™ Copolyester MN631 contains a mold release. It has excellent appearance and is nearly water-clear. Its most outstanding feature is its high flow characteristic, with the ability to fill intricate tooling. Other features include toughness and chemical resistance. It is easy to process with minimal drying time and has good toughness and chemical resistance.

Eastman EastaPure™ DB Solvent is a high boiling, slow evaporating glycol ether providing low trace metals content for sensitive electronic applications.

AP 550-1 (25% in Aromatic 100) is a nonchlorinated polyolefin for improved coating adhesion on TPO and PP. It allows the formulation of melamine-cured systems with excellent performance properties previously only available in 2K systems.

DuraStar™ Polymer DS1910HF, Natural polymer contains a mold release. It has excellent appearance and clarity. Its most outstanding features are chemical resistance and excellent processing characteristics. Easy to process, it flows readily, fills intricate molds, and is well suited for thick-wall applications.

Eastman Neostar™ Elastomer FN005 is a tough, clear, durable, general purpose grade copolyester ether for use in flexible packaging and tubing applications as well as some automotive and profile applications. Target inherent viscosity is 1.05.

Eastman Neostar™ Elastomer FN006 is a tough, clear, durable, general purpose grade copolyester ether for use in flexible packaging and tubing applications as well as some automotive and profile applications. Target inherent viscosity is 1.6.

Eastman Neostar™ FN007 elastomer is a tough, clear, durable, general purpose grade copolyester ether for use in flexible packaging and tubing applications as well as some automotive and profile applications. Target inherent viscosity is 1.23.

This product is a 20% solid solution of Chlorinated Polyolefin 730-1 in Xylene. It is an efficient adhesion promoter in primers to ensure adhesion of color coats and topcoats to polypropylene (PP) and thermoplastic olefin (TPO) substrates. It has excellent humidity and gasoline resistance and superior high temperature performance.

DuraStar™ Polymer DS2000, Natural polymer has excellent appearance and is nearly water-clear. Its most outstanding features are toughness, chemical resistance, and excellent processing characteristics. Easy to process, it flows readily and fills intricate molds.

This product is a 25% solid solution of Chlorinated Polyolefin 730-1 in Aromatic 100. It is an efficient adhesion promoter in primers to ensure adhesion of color coats and topcoats to polypropylene (PP) and thermoplastic olefin (TPO) substrates. It has excellent humidity and gasoline resistance and superior high temperature performance.

DuraStar™ Polymer MN610 Natural polymer has excellent appearance and is nearly water-clear. Benefits include toughness, chemical resistance, and excellent processing characteristics. This product does not contain a mold release.

Eastar™ AN001 copolyester has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. Exposure to aromatic oils often causes crazing or actual fracture of many polymer resins, but AN001 maintains its physical properties when exposed to these oils, and its appearance is virtually unchanged. It is one of our premier materials for the cosmetics and personal care packaging market.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastman Provista™ Copolymer MP001 is a resin specifically developed for extrusion into profiles where aesthetics such as high clarity and gloss, coupled with design flexibility, drive demand. An extremely high melt strength makes the resin an excellent choice when extruding profiles into complicated shapes.

Eastar™ A150 is intended primarily for extrusion into film and sheeting for packaging applications. It has excellent hydrolytic stability and good heat stability.

Eastar™ BR203 copolyester has excellent appearance and is nearly water clear. With superior chemical resistance, it maintains its physical properties and appearance when exposed to aromatic oils. BR203 is specifically formulated to provide the optimal combination of chemical resistance, bristle retention, strength, stiffness, processability, clarity, colorability, and feel for toothbrushes.

Eastman™ Cellulose Acetate (CA-398-10NF/EP) is a low viscosity solution grade of cellulose acetate.

Eastar™ DN010 copolyester is a brilliantly clear polymer having excellent impact strength, chemical resistance, and low shrinkage rates. Eastar DN010 contains no mold release.

Eastar™ DN011 copolyester is a brilliantly clear polymer having excellent impact strength, chemical resistance, and low shrinkage rates. Eastar DN011 contains a mold release.

Eastalloy™ Polymer DA510 is a clear copolyester/polycarbonate alloy. This product has good impact strength, chemical resistance, heat resistance, dimensional stability, and low mold shrinkage.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ MN004 Copolyester contains a mold release to improve ejection. Eastar™ copolyesters are brilliantly clear polymers that have excellent impact strength, chemical resistance, dimensional stability, and low shrinkage rates.

Eastar™ Copolyester DN001HF has excellent flow characteristics while maintaining superior mechanical properties. It is easy to process and has exceptional clarity, toughness, and chemical resistance.

Eastman™ copolyester 1223 is a clear, amorphous material. Because of its clarity, toughness and good melt strength at processing temperatures, it is useful in a variety of processing techniques including film and sheet extrusion.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ Copolyester MN005 has excellent appearance and is nearly water-clear. It is easy to process and can fill intricate tools. Its most outstanding features are exceptional clarity, toughness, radiation resistance, chemical resistance and excellent color and property retention following gamma and e-beam sterilization. MN005 contains a mold release.

Eastman EastaPure™ PM Acetate, Stabilized is manufactured for semiconductor and electronics applications. It is a high-purity solvent which provides greater protection against organic peroxide formation.

EASTMAN Propionic Acid P Grain and Hay Preservative, which has been registered with the Environmental Protection Agency (EPA) as a pesticide and is marketed as a grain and hay preservative.

Eastman Spectar™ Clear copolyester offers the thermoformability and ease of fabrication of Eastman Spectar™ copolyester along with significantly improved clarity and high notch impact strength.

Eastman™ HPHP Glycol is a difunctional ester-glycol used for manufacturing polyester resins for the powder, coil, and automotive coatings market. The cast solid form is shipped in drums requiring a hot room or drum heater to melt the contents for removal.

Drystar™ 0827 Copolyesters display an excellent balance of properties such as superior aesthetics, impact strength, and chemical resistance. This new product-line is designed to meet the needs of converters seeking value-added solutions to their drying requirements of copolyesters.

Drystar™ 0601 Copolyesters display an excellent balance of properties such as superior aesthetics, impact strength, and chemical resistance. This new product-line is designed to meet the needs of converters seeking value-added solutions to their drying requirements of copolyesters.

Drystar™ 0603 Copolyesters display an excellent balance of properties such as superior aesthetics, impact strength, and chemical resistance. This new product-line is designed to meet the needs of converters seeking value-added solutions to their drying requirements of copolyesters

Drystar™ 0325 Copolyesters display an excellent balance of properties such as superior aesthetics, impact strength, and chemical resistance. This new product-line is designed to meet the needs of converters seeking value-added solutions to their drying requirements of copolyesters.

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel. Tenite™ Cellulose Acetate Butyrate 285-04 contains an odor mask and has a plasticizer level of 4%.

Eastman Cristal™ Renew copolyester CN005-25 Natural is a high flow product. Designed specifically for the unique requirements of luxury cosmetic packaging, our premier PCTA copolyester delivers unsurpassed color and clarity and a capability to mold thick parts with superior gate aesthetics.

Eastman Cristal™ copolyester AN014 Natural is a high flow product that contains a mold release. Other outstanding features of Eastman Cristal™ copolyester AN014 Natural are easily maintained such as excellent appearance and clarity, good physical properties, chemical resistance, and easy processing. Eastman Cristal™ copolyester AN014 Natural is approved for food contact. Eastman Cristal™ copolyester AN014 Natural flow lengths are increased 20-40% relative to Eastman Cristal™ copolyester AN004 as shown by spiral flow testing. This high flow product is especially suited for those applications utilizing thin-walled intricate tools. Under existing United States Food and Drug Administration (FDA) regulations, Eastman Cristal™ copolyester AN014 Natural may be used in food contact articles which comply with the specifications and conditions of use in 21 CFR 177.1240.

Eastman Cristal™ copolyester AN004 Natural contains a mold release. It has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. Its processability coupled with its outstanding chemical resistance makes it well suited for thick-wall applications.

Eastman Cristal™ copolyester CN005 is a high flow product. Designed specifically for the unique requirements of luxury cosmetic packaging, our premier PCTA copolyester delivers unsurpassed color and clarity and a capability to mold thick parts with superior gate aesthetics.

Tenite™ cellulosic plastics are noted for their excellent balance of properties - toughness, hardness, strength, surface gloss, clarity, and a warm feel.

Eastman™ DOA plasticizer (Bis(2-Ethylhexyl) Adipate), Kosher is a light colored, oily liquid generally used as a plasticizer for PVC. Eastman™ DOA plasticizer is used to produce clear films for food packaging applications.

Eastman Sustane™ SAIB CO Food Grade is a free-flowing liquid with a viscosity of less than 4,000 cP at room temperature.

Eastman Eastobond™ Copolyester 19412 is a plastic lidding film resin designed to adhere directly to monolayer PET food trays, rendering them recyclable.

Eastman Cellulose Acetate Butyrate CAB-171-15 has the lowest butyryl content and the lowest degree of solubility in the Eastman cellulose ester product line. Films prepared with this ester offer superior toughness and hardness when compared with films prepared from other mixed esters.

Propionic Acid is a colorless, oily liquid that is miscible in water. This product is used when a food grade product is required in the food industry to produce esters, salts, and other derivatives.

Eastman Propionic Acid Feed Grade is required for animal feed use, and can be used as a mold inhibitor for formula feed.

This product is offered for animal feed use. It can be used as a mold inhibitor for formula feed.

Eastman™ Acetaldehyde, Kosher is a highly reactive, flammable, colorless liquid. Acetaldehyde undergoes the general reactions of aldehydes and is important for numerous condensation, addition, and polymerization reactions.

Eastalloy™ DA003-8999K is a clear copolyester/polycarbonate alloy. This product has good impact strength, chemical resistance, dimensional stability and low shrinkage rates.

This grade of acetic acid meets the requirements of the U. S. Pharmacopeia (USP) and is produced under appropriate current good manufacturing practices (cGMP) for use in the production of pharmaceuticals.

This grade of glacial acetic acid meets the requirements of the Food Chemical Codex and is produced under appropriate current good manufacturing practices (cGMP) for use as a food additive.

Eastman™ IBIB is a slow-evaporating, economical retarder solvent used in nitrocellulose lacquers, coatings for plastic substrates, and high solids coatings. It exhibits high electrical resistance and low surface tension.

Excellent coalescing aid, particularly under adverse conditions of high humidity and low temperature. Excellent properties with associative thickeners. Useful as a slow evaporating solvent in polyester coil coatings and high bake enamels.

n-Butyronitrile is a clear, colorless liquid at room temperature. It is used in pharmaceutical, agricultural, and process solvent applications.

Eastman NPG (Molten) is the industry standard glycol component in high-quality polyester resins for industrial coatings and fiberglass-reinforced plastics applications. The bulk molten form is shipped in tank trucks that require a heated tank for storage.

Eastman™ MIPK is a water-white liquid with a low boiling point.

Eastman™ butyraldehyde is used as a fragrance intermediate.

Eastman Isobutyraldehyde, Dry is a colorless, flammable liquid, and is used primarily as a chemical intermediate.

Eastman NPG 90 is the industry standard glycol component in high-quality polyester resins for industrial coatings and fiberglass-reinforced plastics applications. This product is 90 parts NPG™ and 10 parts water, a liquid at or above 38°C, and delivered in bulk.

Eastman™ PM Solvent, a medium-boiling glycol ether, is an active solvent for cellulose acetate butyrate, nitrocellulose, epoxy, phenolic, acrylic, and alkyd resins. It is used in a variety of coating, printing ink, and cleaning applications.

Eastman™ PM Acetate is a slow evaporating solvent with both ether and ester functional groups. It is a colorless liquid with a mild odor used as an effective retarder solvent as well as being an excellent solvent for many coating polymers.

Eastman™ DE HG solvent is a blend of Eastman DE glycol ether and EG (70/30 wt. %). It is a colorless liquid, has very mild odor, and completely water miscible. It is used as a coalescent in latex paints and in floor polishes.

Eastman DP Solvent (Diethylene Glycol Monopropyl Ether) is a slow-evaporating, water-miscible solvent useful in solution and water-based coatings. It is an active solvent for many coating materials and demonstrates very good coupling efficiency with resin systems in water-based coatings. Additionally, its low odor is advantageous in formulating printing inks and can be used in aqueous cleaners.

Eastman™ EP Solvent (Ethylene Glycol Monopropyl Ether) is colorless and water-miscible over a wide range of temperatures with a slow evaporation rate. It is used in coatings and inks where a milder, less detectable odor is required and provides good viscosity control and high flash point. It can also be used to develop customized aqueous cleaners.

Eastman™ DB Solvent, Stabilized is a high-boiling glycol ether used in baking enamels, printing inks, textile dyeing, or as a coalescent in latex paints. This grade contains BHT antioxidant.

Eastman™ Ethyl Acetate, Spectro Grade is a colorless, fragrant, low-boiling, fast evaporating solvent. This product is available as 99.9% pure.

Eastman TMPD™ is used to formulate saturated polyester resins for liquid coatings and unsaturated polyester laminating resins sold into a wide variety of markets. This form of Eastman TMPD™ is supplied as white, waxy platelets that are shipped in bags.

Eastman™ EP Solvent is colorless and water-miscible over a wide range of temperatures with a slow evaporation rate. It is used in coatings where a milder, less detectable odor is required. This product is stabilized with BHT.

For applications in drugs, foods, or feeds, Eastman provides glacial acetic acid in grades appropriate for these regulated uses.

Eastman™ Butyl Acetate is a medium-boiling ester solvent with an evaporation rate of 1.0 making it ideal for quick drying nitrocellulose lacquers. A colorless liquid with a fruity odor, it is an active solvent for film-formers.

Eastman™ Triacetin is used as a plasticizer for cellulosic resins and is useful for imparting plasticity and flow to laminating resins. It is also used as a plasticizer for vinylidene polymers and copolymers. It is an ingredient in inks for printing on plastics, and as a plasticizer in nail polish.

Eastman™ Propyl Acetate is a colorless liquid with a mild, fruity odor. It is an active solvent for nitrocellulose, cellulose acetate butyrate, polyester, alkyd, and acrylic resins. It has a medium evaporation rate and is a non-HAP solvent.

Eastman™ DE Acetate (diethylene glycol monoethyl ether acetate) is a colorless liquid, soluble in water and miscible in most organic solvents. It is primarily used as a coalescing aid in paints and as a solvent in inks. With broad resin solubility, it is suitable for use in coil coatings.

The high solvent activity, slow evaporation rate, low density and surface tension, and high boiling point of Eastman™ MAK (Methyl n-Amyl Ketone) make it ideal in formulating high solids coatings that meet VOC guidelines.

Eastman TEG-EH (Triethylene Glycol Bis (2-Ethylhexanoate)) plasticizer is usually blended with plasticizers in PVC. For PVB resins, Eastman TEG-EH offers low viscosity for ease of compounding and low color for excellent clarity in automotive and residential and commercial window applications.

Food Contact Status compliant – Eastman™ DOP plasticizer (Bis(2-Ethylhexyl) Phthalate) is a light colored, low volatility, odorless liquid. It is the most widely used all-purpose plasticizer offered by Eastman for use with PVC resins. It features good stability to heat and ultraviolet light, a broad range of compatibility, and excellent resistance to hydrolysis.

Eastman™ DOA plasticizer (Bis(2-Ethylhexyl) Adipate) is a light colored, oily liquid generally used as a plasticizer for PVC. Eastman™ DOA features flexibility at low temperatures, good electrical properties, good resistance to weathering, and good stability to heat.

TEP is a clear, colorless liquid with a mild odor useful as a solvent in many applications, a plasticizer in tough, fire-resistant plastics, and as an agricultural chemical intermediate.

Eastman™ 2-Ethylhexanoic Acid is a colorless, high-boiling liquid having a mild odor. The metallic salts of Eastman™ 2-ethylhexanoic acid are used as driers for odorless paints, inks, varnishes, and enamels.

Eastman™ DIBK (Diisobutyl Ketone) is a slow-evaporating, low-density solvent that has good activity for many synthetic resins. It is useful as a retarder solvent to improve flow and minimize humidity blushing.

Eastman™ SAIB-90EA is a stable liquid that has a light color, as well as good thermal, hydrolytic, and color stability. It is a blend of sucrose acetate isobutyrate with about 10% ethyl acetate, providing a low viscosity liquid that is easy to work with. It is well-suited for coatings and nail polish lacquers.

Eastman™ SAIB-100 (Sucrose Acetate Isobutyrate) is an odorless and tasteless, thermally stable, viscous liquid with a very light color. The electrical properties of Eastman™ SAIB are equal to or better than those of many plasticizers and it possesses an especially high volume resistivity.

Eastman™ 2-Ethylhexyl Acetate is a high-boiling retarder solvent with low water solubility, mild odor, and a slow evaporation rate. It is used to promote flow and retard blushing in lacquers, NC lacquer emulsions, screen inks, baking enamels and air-dry enamels.

The high solvent activity, slow evaporation rate, low density and surface tension, and high boiling point of Eastman™ MIAK (Methyl Isoamyl Ketone), make it ideal in formulating low-viscosity, high solids coatings with reduced VOC.

Eastman™ EB Acetate (Ethylene Glycol Monobutyl Ether Acetate) is a high-boiling glycol ether-ester. Its slow evaporation rate provides excellent flow and leveling in high-bake coatings as well as air-dry systems such as epoxy coatings. It has limited water miscibility. It is supplied as a urethane grade solvent.

Eastman DB Acetate (Diethylene Glycol Monobutyl Ether Acetate) is a high-boiling ester widely used as a solvent in printing inks and high-bake enamels; it is also used as a coalescing aid in low pH latex paints. It is especially applicable in screen inks and as a component in coil coatings. It has also found use as a coalescing aid, a coil coating component, and in the separation of alcohols and ketones by distillation.

Eastman Ethylene Glycol Diacetate (EGDA) is a colorless, low odor, very slow-evaporating solvent that gives good flow-out to baking lacquers and enamels. Major uses include thermoplastic acrylic coatings as a reflow solvent and in foundry core-binding applications.

Eastman™ Methyl Isobutyl Ketone (MIBK) is a medium-evaporating, low density, highly active solvent for use in inks, coatings, and adhesives. It is also used in a wide variety of other applications and markets.

Eastman Sustane™ SAIB (Sucrose Acetate Isobutyrate) Food Grade, Kosher is a high purity distilled product that is odorless and tasteless at levels used in beverages. It is used primarily in citrus beverages as a weighting agent or flavor emulsion stabilizer to prevent separation of essential citrus oils.

Eastman™ TOTM plasticizer (Tris (2-Ethylhexyl) Trimellitate) is the ideal PVC plasticizer for use in applications where low volatility is of supreme importance, such as wire and cable insulation and interior automotive. It also has properties that are required for dishwasher gaskets and photograph storage.

Eastman™ SAIB-90 (Sucrose Acetate Isobutyrate) is a stable liquid that has a light color, as well as good thermal, hydrolytic, and color stability. It is a blend of sucrose acetate isobutyrate with about 10% denatured ethanol, providing a low viscosity liquid that is easy to work with. This product is well-suited for coatings and nail polish lacquers.

Acetic Anhydride is manufactured by Eastman and supplied in various grades.

Eastman™ MPK (Methyl n-Propyl Ketone) is a medium evaporating, urethane-grade solvent. It is an active solvent for most synthetic resins including acrylics, polyesters, cellulosics, epoxies, vinyls, and alkyds. Its high solvency, low density, and medium evaporation rate make it attractive as a letdown solvent for high-solids resins used in formulating coatings with low VOC content. It is used in gravure printing inks and also provides excellent performance for a wide range of cleaning and surface preparation applications for the transportation industry.

Eastman Methyl Acetate is an active, fast evaporating, mild odor solvent for a broad range of coating and ink resins. It is useful in applications where fast solvent release and quick dry-to-touch times are required. Methyl acetate is a VOC-exempt, non-HAP, non-ODS, readily biodegradable solvent that can be used in blends to develop environmentally friendly cleaners.

Eastman C-11 Ketone is a low-cost, slow-evaporating, low-density mixture of ketone solvents. It is useful as a retarder solvent for primers, coil coatings, maintenance coatings and high-solids enamels. In these coatings, it improves gloss and leveling, reduces orange peel, minimizes solvent popping, and helps reduce VOCs. In many coatings, it can be used alone or blended with other solvents to replace isophorone and dibasic esters. Eastman C-11 Ketone has good solvency for a wide range of resins including nitrocellulose, alkyds, polyesters, acrylics, epoxies, and some vinyl chloride/vinyl acetate copolymers. Compared with other solvents in the same evaporation range, C-11 Ketone often offers an economic advantage.

Eastman™ Glacial Acetic Acid/Acetic Anhydride 40/60 Blend is for general industrial uses.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 90% dilution strength.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 84% dilution strength.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 80% dilution strength.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 70% dilution strength.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 56% dilution strength.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 95% dilution strength.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 92% dilution strength.

Eastman™ Triacetin, Kosher, Food Grade, meets all Food Chemicals Codex (FCC) specifications and is manufactured under good manufacturing practices (GMP). One of its main uses is as a plasticizer in chewing gum.

Eastman™ Triacetin, Food Grade is used as an ingredient in many food and cosmetic products. Its high solvency power and low volatility make triacetin a good solvent and fixative for many flavors and fragrances. One of its main uses is as a plasticizer in chewing gum.

CHDA is a cycloaliphatic diacid for use in polyester resins for coatings and fiberglass-reinforced plastics. It is also ideally suited improving performance of waterborne, high solids, powder coatings and coil coating applications. CHDA is supplied as white to off-white powder in various package sizes.

Eastman EastaPure™ MAK (Methyl n-Amyl Ketone) is being offered for positive photoresist formulations. It is a high-purity, low-trace metal solvent.

Acetic Acid is supplied by Eastman in several dilution strengths. Many users prefer a diluted form of the product to avoid the expense of heated storage tanks. This product is 60% dilution strength.

Acetic Anhydride is supplied in various grades. This product is the kosher grade and may be used in foods as a reactant only.

This grade of glacial acetic acid meets the requirements of the Food Chemical Codex and is produced under appropriate current good manufacturing practices (cGMP) for use as a food additive.

Eastman™ Propionic Anhydride is a colorless liquid having a pungent odor and high boiling point. It is soluble in alcohol, ether, chloroform, and alkalies, but decomposes in water.

Eastman™ n-Butyric Anhydride is a water-white liquid that hydrolyzes to butyric acid. It has a minimum assay of 98%.

Eastman™ Butyric acid (C₃H₇COOH) is a clear, colorless liquid, with a strong pungent odor. Esters and salts of butyric acid are used in a variety of applications including perfumes, flavorings, and animal feeds.

This product is a general sales grade Propionic Acid and may be used to produce numerous esters, salts, and other derivatives for use in the plastics, coatings, agricultural chemicals, food, flavor, and perfume industries.

Isobutyric Anhydride is a liquid with a boiling range of 180-187°C. It is used primarily in chemical processing and as a chemical intermediate.

Eastman Cellulose Acetate CA-398-3 is one of the lower viscosity solution grades of cellulose acetate with an average ASTM viscosity of 3 seconds. Blended with appropriate solvents, plasticizers, and other modifying resins, it is used in coatings formulations for a variety of substrates. This multipurpose rheology enhancer provides high strength and good resistance to ultraviolet light, heat, oils and greases. It is useful in lacquers for glass, plastic, wire and release coatings.

Eastman Cellulose Acetate CA-398-6 is a low-viscosity solution grade cellulose acetate supplied in the form of fine, dry, free-flowing powder.

Eastman Cellulose Acetate CA-398-10 is a low-viscosity solution grade of cellulose acetate. It is used in a variety of coatings applications, pressure-sensitive tapes, and wood sealers.

Eastman™ Cellulose Acetate Propionate CAP-482-0.5 is a low odor, free-flowing powder and is especially suitable for use in inks, overprint varnishes, and nail lacquer topcoats.

Eastman Cellulose Acetate Butyrate CAB-553-0.4 is soluble in low molecular weight alcohols as well as other common organic solvents. It has alcohol solubility with excellent compatibility and pigment-wetting characteristics. High hydroxyl content allows a high level of crosslinking. It will produce colorless films with good ultraviolet stability and is supplied as dry, free-flowing powder, offering maximum formulating convenience and flexibility.

Eastman Cristal™ One E is a copolyester designed for to be fully compatible with the PET recycling stream for extrusion-blown molded bottles for the skincare, personal care and color cosmetics markets.

Eastman Cristal™ One E Renew-30 is a copolyester designed for to be fully compatible with the PET recycling stream for extrusion-blown molded bottles for the skincare, personal care and color cosmetics markets.

Eastman Cristal™ One E Renew-50 is a copolyester designed for to be fully compatible with the PET recycling stream for extrusion-blown molded bottles for the skincare, personal care and color cosmetics markets.

Eastman Tritan MXF321 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability. Eastman Tritan MXF321 contains a mold release derived from vegetable based sources.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastman Tritan™ MX811 is an amorphous copolyester with excellent appearance and clarity. Tritan MX811 contains a mold release derived from vegetable based sources. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new generation copolyester can also be molded into various applications without incorporating high levels of residual stress.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastman Tritan™ MX711 copolyester has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, and chemical resistance. Tritan MX711 has been formulated for medical devices.

Eastman Cristal™ One E Renew-100 is a copolyester designed for to be fully compatible with the PET recycling stream for extrusion-blown molded bottles for the skincare, personal care and color cosmetics markets.

Eastman Tritan MXF321 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability. Eastman Tritan MXF321 contains a mold release derived from vegetable based sources.

Eastman Tritan MXF321HF copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321HF has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321HF has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability to fill complex parts. Tritan MXF321HF contains a mold release derived from vegetable-based sources.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastman Tritan™ MX711 copolyester has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, and chemical resistance. Tritan MX711 has been formulated for medical devices.

Eastman Tritan MXF321HF copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321HF has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321HF has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability to fill complex parts. Tritan MXF321HF contains a mold release derived from vegetable-based sources.

Eastman Tritan™ Renew LX101-30 is an amorphous copolyester with excellent appearance and clarity. Tritan Renew LX101-30 can easily be converted into articles for application in Consumer and Personal Care markets by injection molding, extrusion blow molding, and injection blow molding.

Eastman Tritan™ Renew LX101-50 is an amorphous copolyester with excellent appearance and clarity. Tritan Renew LX101-50 can easily be converted into articles for application in Consumer and Personal Care markets by injection molding, extrusion blow molding, and injection blow molding.

Eastman Tritan™ Renew LX150HF-30 copolyester is a high flow grade of an amorphous copolyester with excellent appearance and clarity. Tritan Renew LX150HF-30 has viscosity reductions of 40-50% relative to standard grades of Tritan.

Eastman Tritan™ Renew LX150HF-50 copolyester is a high flow grade of an amorphous copolyester with excellent appearance and clarity. Tritan Renew LX150HF-50 has viscosity reductions of 40-50% relative to standard grades of Tritan.

Eastman Tritan™ Renew LX151HF-50 is a high flow grade of an amorphous copolyester with excellent appearance and clarity. Tritan Renew LX151HF-50 has viscosity reductions of 40-50% relative to standard grades of Eastman Tritan.

Eastman Cristal™ One Pro MR is a copolyester product that contains mold release for ease of injection. It is designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough and exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to approximatively 12mm), while maintaining clarity and color.

Eastman Tritan™ Renew LX151HF-30 is a high flow grade of an amorphous copolyester with excellent appearance and clarity. Tritan Renew LX151HF-30 has viscosity reductions of 40-50% relative to standard grades of Eastman Tritan™.

Eastman Tritan™ Renew EX501-50 is an amorphous copolyester specifically developed for the Infant Care market. Its most outstanding features are consistent glass-like clarity even after multiple dishwasher cycles.

Eastman Tritan™ Renew LX100-30 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance.

Eastman Cristal™ One Pro MR Renew-50 is a copolyester that contains mold release for ease of ejection. It is designed to be fully compatible with the PET recycling stream.

Eastman Cristal™ One Pro MR Renew-30 is a copolyester that contains mold release for ease of injection. It is designed to be fully compatible with the PET recycling stream.

Eastman Cristal™ One MR is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough and exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal One MR is recommended for thicker luxury bottles with complex shapes.

Eastman Tritan™ Renew LX500-50 is an amorphous copolyester specifically developed for use in blow molding applications for the cosmetic, fragrance, and personal care markets.

Eastman Tritan™ Renew LX500-30 is an amorphous copolyester specifically developed for use in blow molding applications for the cosmetic, fragrance, and personal care markets.

Eastman Tritan™ Renew LX100-50 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance.

Eastman Spectar™ Renew 14471-30 copolyester is a sparkling, clear plastic material that is increasingly popular for protective barriers used to limit the spread of viruses like COVID-19, including sneeze guards. Spectar™ 14471-30 is an ideal solution for displays/in-store fixtures. For these applications, Spectar is a proven alternative to polycarbonate and acrylic.

Eastman Cristal™ One Pro Renew-25 is a copolyester designed to be fully compatible with the PET recycling stream.

Eastman Eastar™ Renew DN501-10 copolyester is a high flow product designed and engineered for many different applications. With its excellent color and clarity and its ability to mold thick parts with improved gate aesthetics, Eastar™ Renew DN501-10 is clearly a well-suited copolyester for many applications. Other outstanding features are excellent chemical resistance, high gloss, and improvements in processing such as faster cycle times, and lower scrap rates. Eastar™ Renew DN501-10 is also ideally suited for two-shot molding due to its lower processing temperatures, very slow crystallization rate, and flow characteristics. Eastar™ Renew DN501-10 contains a mold release derived from vegetable based sources.

Eastman Eastar™ EB364 is a copolyester designed to be fully compatible with the PET recycling stream for extrusion-blown molded bottles for the beverage, food, and homecare markets.

Eastman Cristal™ One Renew-25 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough and exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One Renew-25 is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ Renew copolyester EN067-25 is a copolyester designed to be fully compatible with the PET recycling stream.

Eastman Cristal™ Renew copolyester EN076-25 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging with a combination of good color and high clarity for molded parts with an RIC1 resin.

Eastman Cristal™ One E Renew-25 is a copolyester designed to be fully compatible with the PET recycling stream for extrusion-blown molded bottles for the skincare, personal care and color cosmetics markets.

Eastman Cristal™ One Pro MR Renew-25 is a copolyester that contains mold release for ease of injection. It is designed to be fully compatible with the PET recycling stream.

Eastman Cristal™ One Renew-25 MR is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough, exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One Renew-25 MR is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ One Renew-50 MR is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough, exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One Renew-50 MR is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ One Renew-30 MR is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough, exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One Renew-30 MR is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ Renew copolyester AN014-30 Natural is a high flow product that contains a mold release.

Eastman Cristal™ Renew copolyester AN014-50 Natural is a high flow product that contains a mold release.

Eastman Cristal™ copolyester AN001 Natural has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. Exposure to aromatic oils often causes crazing or actual fracture of many polymer resins, but Eastman Cristal™ copolyester AN001 Natural maintains its physical properties when exposed to these oils, and its appearance is virtually unchanged. It is one of our premier materials for the cosmetics and personal care packaging market.

Eastman Cristal™ Renew copolyester AN004-30 Natural contains a mold release. It has an excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. Its processability coupled with its outstanding chemical resistance makes it well suited for thick-wall applications.

Eastman Cristal™ Renew copolyester AN004-50 Natural contains a mold release. It has an excellent appearance and is nearly water clear. Its most outstanding features are its chemical resistance and processing capabilities. These features make it well suited for thick-wall applications.

Eastman Eastek 4100 is a high-performance polyester resin for polyurethane hot melt adhesive applications. Eastman Eastek 4100 resin is designed to improve cross linking, increase Tg, and improve formulation flexibility. These attributes enable greater productivity, application consistency, long-term durability, and expanded application space for woodworking, packaging, assembly, and automotive applications.

MP2104 formulations are designed for gold-coated 3-piece cans and bodies with sanitary or easy-open ends for both easy-to-hold and hard-to-hold foods and beverages. Resin provides improved functionality to benefit gold phenolic coatings and offers broad formulation latitude.

Eastman Cristal™ One Pro is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough and exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to approximatively 12mm), while maintaining clarity and color.

Eastman Cristal™ One is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough and exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal One is recommended for thicker luxury bottles with complex shapes.

Eastman Acitra™ LF10 Na is a liquid preservative to protect feeding stuffs against deterioration caused by a broad spectrum of microorganisms.

Eastman Acitra™ LF10 Na is a liquid preservative to protect feeding stuffs against deterioration caused by a broad spectrum of microorganisms.

Eastman Acitra^TM LF30 Na is a liquid preservative to protect feeding stuffs against deterioration caused by a broad spectrum of microorganisms.

Tritan™ Renew VX301-50 is an amorphous copolyester with excellent clarity and impact resistance. The outstanding chemical resistance, hydrolytic stability, and ease of processing make Tritan™ Renew VX301-50 an ideal candidate for optical applications such as eyewear frames.

Eastman Cristal™ One Renew-50 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough, exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ One Pro Renew-50 is a copolyester designed to be fully compatible with the PET recycling stream.

GBM Performant is a free flowing, dust free complementary feed containing fat coated butyrate that helps improve zootechnical performance and supports metabolism.

GBM Enhanced is a free flowing, dust-free premixture of fat coated butyrate and other functional ingredients. GBM Enhanced maintains an optimal gut health and butyrate content helps improve the feed conversion ratio and supports a healthy metabolism

GBM Enhanced T is a free-flowing complementary feed containing encapsulated calcium butyrate that helps improve zootechnical performance and supports metabolism. In addition it also contains calcium lactate and chestnut extract.

GBM Microclassic is a free flowing, dust-free complementary feed containing micro granulated calcium butyrate that helps improve zootechnical performance and supports metabolism.

Eastman Cristal™ Renew copolyester EN076-30 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging with a combination of good color and high clarity for molded parts with an RIC1 resin.

Eastman Cristal™ Renew copolyester EN076-50 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging with a combination of good color and high clarity for molded parts with an RIC1 resin.

Eastman Cristal™ Renew copolyester CN015-75 Natural is a high flow product that contains a mold release to provide ease of demolding.

Eastar™ Renew AN004-50 Natural copolyester contains a mold release. It has an excellent appearance and is nearly water clear. Its most outstanding features are its chemical resistance and processing capabilities. These features make it well suited for thick-wall applications.

Eastman Cristal™ Renew copolyester AN004-80 Natural contains a mold release. It has an excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities. These features make it well suited for thick-wall applications.

Eastman Cristal™ Renew Copolyester AN014-80 Natural is a high flow product that contains a mold release.

Eastman Cristal™ Renew copolyester AN001-50 Natural has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities.

Eastman Cristal™ Renew copolyester AN001-80 Natural has excellent appearance and is nearly water-clear. Its most outstanding features are its chemical resistance and processing capabilities.

Eastman Cristal™ Renew copolyester CN015-30 Natural copolyester is a high flow product that contains a mold release to provide ease of demolding.

Eastman Eastobond™ Renew copolyester 19412-100 is a plastic lidding film resin designed to adhere directly to monolayer PET food trays, rendering them recyclable.

Eastman Triacetin Renew 59 is used as a plasticizer for cellulosic resins and is compatible in all proportions with cellulose acetate, nitrocellulose, and ethyl cellulose. It is useful for imparting plasticity and flow to laminating resins, particularly at low temperatures, and is also used as a plasticizer for vinylidene polymers and copolymers. Eastman Renew plasticizers have been certified by International Sustainability & Carbon Certification (ISCC), a global, independent agency that tracks sustainable content in a variety of industries.

Eastman Cellulose Acetate Butyrate CAB-381-0.5, Food Contact is a cellulose ester with medium butyryl content and low viscosity. It was designed for use where low application viscosities at relatively high solids levels is needed. It is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate Butyrate (CAB-551-0.01, Food Contact) has many unique attributes that will serve useful across many different coating application areas. It has the lowest Tg (glass transition temperature) of the CAB portfolio. It also has the second lowest M(n), which enables its compatibility with other coatings components. It is compatible with numerous cross-linking resins and has a lower solution viscosity.

Eastman Cellulose Acetate Butyrate CAB-551-0.2, Food Contact is a cellulose ester with high butyryl content and relatively low molecular weight. Its good compatibility with various resin systems and its solubility in a wide variety of solvents make it useful as an additive in numerous coating compositions, including high-solids and thermoset coatings, and as a modifier for UV-curing systems.

Eastman Cellulose Acetate Butyrate CAB-381-0.1, Food Contact is a cellulose ester with medium butyryl content and low viscosity. It was designed for use where low application viscosities at relatively high solids levels are needed. CAB-381-0.1, Food Contact is used when lower viscosity for higher solids formulations and increased toughness with excellent surface hardness is desired. It is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate CA-398-3, Food Contact is one of the lower viscosity solution grades of cellulose acetate with an average ASTM viscosity of 3 seconds. Blended with appropriate solvents, plasticizers, and other modifying resins, it is used in coatings formulations for a variety of substrates. This multipurpose rheology enhancer provides high strength and good resistance to ultraviolet light, heat, oils and greases. CA-398-3 is used in lacquers for glass, plastic, wire and release coatings.

Eastman Cellulose Acetate Propionate CAP-482-0.5, Food Contact is a low odor, free-flowing powder and is especially suitable for use in inks, overprint varnishes, and nail lacquer topcoats. It is compliant with FDA additive regulations for use in certain food-contact applications.

Eastman Cellulose Acetate Butyrate CAB-381-20, Food Contact is a cellulose ester with medium butyryl content, very high ASTM(A) viscosity, and great rheological modification. It offers a combination of solubility and compatibility, moisture resistance, excellent surface hardness and good film strength. It is supplied as a dry, free-flowing powder.

Eastman Cellulose Acetate Butyrate CAB-381-2, Food Contact is a cellulose ester with medium butyryl content and high viscosity. It offers a combination of solubility and compatibility, moisture resistance, excellent surface hardness, and good film strength. It is supplied as a dry, free-flowing powder.

AIV 2000 Plus Na is a formic acid based product recommended for pre-wilted silage, and crimping applications.

Eastman™ Ethylene Glycol, Polyester Grade is a high purity grade of ethylene glycol with excellent appearance and clarity. Eastman™ Ethylene Glycol, Polyester Grade is used for manufacturing polyester fibers and polyethylene terephalate (PET) resins.

AIV&reg; 2 Plus Na is a concentrated formic acid-based product, used for anaerobic preservation of silage and also to control growth of bacteria and yeasts in liquid feed and easily spoiled fresh feed.

Eastman Protural™ is a solid zootechnical feed additive for application in weaning piglets improving their performance.

Eastman Protural™ is a solid zootechnical feed additive for application in weaning piglets improving their performance.

Eastman™ Formic Acid 85 Na Feed is a liquid preservative to protect feeding stuffs against deterioration caused by a broad spectrum of microorganisms.

Eastman Enhanz™ reduces the feed conversion rate and effects of oxidative stress and improves the digestibility of proteins and fat.

Eastman Mould Control LF2 Na is a buffered liquid blend, especially developed for grain treatment, for storage times up to 12 months.

AIV&reg; Ässä Na is an advanced formic acid-based product having a broad inhibitory effect on spoilage micro-organisms.

Eastman Solus™ 2100, Food Contact performance additive is designed as a rheology control additive for high solids 2K coatings. It is a dry, free-flowing powder that is convenient to handle. It is soluble in a wide range of solvents and compatible in most high solids coatings systems.

Eastar™ EN001 is a clear copolyester for single use food and beverage and general purpose packaging. It is designed for injection stretch blow molding (ISBM) and has enhanced processing capability compared to commodity PET.

Eastman™ Stabilizer Pig Na is used in liquid pig feed to control pH and bacteria growth in mixing tank and in feeding pipeline and valves.

Eastar™ copolyester DG021 contains 20% glass fiber as well as a mold release agent derived from vegetable based sources.

Eastman Protaq™ LF1 Na is a complementary feed to be used in drinking water to reduce the pH of the drinking water and the stomach.

Eastman Protaq^TM LF3 Na is a complementary feed to be used via drinking water for broilers.

Eastman Tetrashield™ IC3000 is a durable polyester resin system that improves the performance of both clearcoats and pigmented topcoats.

INCI: <I>retinyl linoleate</I></br>A naturally derived pro-retinol composed of retinol and high-purity linoleic acid from safflower oil, Eastman GEM retinyl linoleate is a biobased, formulation-stable, easy-to-handle, nonirritating antiaging ingredient. At room temperature, it is a pourable liquid and is supplied as a high-purity (>95%) assay; therefore, it is free of solvent, diluents, and carriers.</br></br>Eastman GEM retinyl linoleate is approved in China.

In Europe, the feed additive formic acid is authorized for the following functions: preservative, silage additive and hygiene condition enhancer.

Eastman Tetrashield™ PC4000 is a high performance polyester resin system for 2K topcoats.

A versatile amorphous polymer, the properties of Eastman GMX200 enable it to be used in a broad array of manufacturing processes including injection molding, injection stretch blow molding, reheat stretch blow molding, and extrusion. The unique impact and heat resistance properties of Eastman GMX200 copolyester can extend the life span of containers that are historically viewed as single use products.

<p>Eastman™ Formic Acid 75 Feed is a liquid preservative to protect feeding stuffs against deterioration caused by a broad spectrum of micro-organisms.

AIV 3 Plus Na is a formic acid-based product used for pre-wilted silage (DM 25 - 45%) and crimping applications.

Eastman Cellulose Acetate Butyrate CAB-531-1, Food Contact is a cellulose ester with a higher butyryl level than CAB-381 series esters. It offers improved compatibility, and due to its flexibility, it requires lower plasticizer modification. When combined with thermoplastic acrylic resins, it produces tough, weather and mar resistant films.

Eastman Cellulose Acetate Butyrate CAB-553-0.4, Food Contact is soluble in low molecular weight alcohols as well as other common organic solvents. It has alcohol solubility with excellent compatibility and pigment-wetting characteristics. High hydroxyl content allows a high level of crosslinking. CAB-553-0.4, Food Contact will produce colorless films with good ultraviolet stability and is supplied as dry, free-flowing powder, offering maximum formulating convenience and flexibility.

Eastman Cellulose Acetate Propionate CAP-482-20, Food Contact has similar characteristics to CAP-482-0.5, but with a higher viscosity. It is useful as a film former in inks and overprint varnishes.

Eastman Sodium Benzoate Feed, reduces clostridial activity, proteolysis and dry matter losses during ensiling.

Eastman Tetrashield™ IC3020 is a high performance resin system for 2K topcoats.

Eastman GMX201 Copolyester contains a mold release derived from vegetable-based sources. A versatile polymer, the properties of Eastman GMX201 Copolyester enable it to be used in a broad array of manufacturing processes including injection molding, injection stretch blow molding, reheat stretch blow molding, and extrusion. The unique impact and heat resistance properties of Eastman GMX201 Copolyester can extend the life span of containers that are historically viewed as single use products.

Eastar™ copolyester DG011 contains 10% glass fiber as well as a mold release agent. Its most outstanding features are excellent chemical resistance, toughness, heat resistance, contact clarity, ease of processing, hydrolytic stability, and increased modulus or stiffness.

Eastman TREVA GC6011 is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Esters and salts of butyric acid are used in a variety of applications including perfumes and flavorings.

Eastman™ Butyric Acid Feed is a clear, colorless liquid, with a strong pungent odor. It is a synthetic chemically defined flavoring, authorized to be used in all type of feeding stuffs for all animal species.

Esters and salts of butyric acid are used in a variety of applications including perfumes and flavorings. This grade of butyric acid is produced under rabbinical supervision in full accordance with Jewish dietary law including Passover.

Eastman™ Stabilizer Crimp is a specialty product for crimping.

Eastman TREVA GC6021 is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman Tritan™ HM1020 copolyester contains 10% glass fiber, as well as a mold release agent derived from vegetable based sources.

Eastman Tritan™ HM1040 copolyester contains 20% glass fiber, as well as a mold release agent derived from vegetable based sources.

Eastman MXF221 copolyester is an amorphous material. Eastman MXF221 copolyester contains a mold release derived from vegetable based sources.

DIMLA TM 1214 RSPO MB mainly contains alkyldimethylamines with chain length C12 and C14. The product is a clear to slighty yellow liquid at room temperature and has the characteristic odor of fatty amines.

AdapT 251 is a formulated MDEA-based solvent designed for total removal of acid gases from natural gas streams.

AdapT 253 is a formulated MDEA-based solvent designed for total removal of acid gases from natural gas streams.

Eastman™ NB3HB solvent is an ester alcohol solvent that offers an exceptional combination of performance, safety, and value.

Therminol 54 is a synthetic fluid designed to provide reliable, consistent heat transfer performance over a long service life at maximum bulk temperatures up to 280°C (540°F).

Eastman Tritan™ HM1060 copolyester contains 30% glass fiber as well as a mold release agent derived from vegetable based sources.

Resin Dispersion 38276 is an anionic, aqueous, solvent-free, and APE (alkylphenol ethoxylate) free dispersion of a stabilized rosin ester.

Cedroz™ is an innovative new post-planting, terpene-based nematicide for the control of root-knot nematodes in fruit and vegetables.

Eastman TRĒVA™ is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman AWI 5010 polymer additive adds heat resistance and anti-blocking properties to ink applications.

Eastman™ Propcorn NC is a non-corrosive propionic acid-based product for aerobic preservation and for improved aerobic stability of crimped feeds and haylage.

Eastman Propcorn™ Plus is a highly concentrated, slightly buffered liquid blend of propionic acid and its ammonium salt for mold control in feedingstuffs and for improving aerobic stability after silo opening by controlling yeasts and molds.

Eastman ProGIT SF2 prevents the growth of harmful bacteria in the feed and improves the quality and shelf life.

Eastman Mould Control LP3 NC is a non-corrosive propionic acid-based liquid product for aerobic preservation against molds in feedstuffs.

Eastman Bacteria Control SF1 preserves compound feeds and raw materials and prevents recontamination micro-organisms.

Eastman ProGIT SF1 prevents the feed against deterioration by micro-organisms and improves the quality and shelf-life of the feed.

Eastman ProGIT SF3 prevents the feed against deterioration by microorganisms and improves the quality and shelf life of the feed.

AdapT 115 is a clear hygroscopic liquid with an amine-like odor. The product as supplied is colorless, but prolonged storage may cause a yellowish discoloration.

MP2101 formulations are designed for applications which require improved flexibility, such as easy-open end (EOE) applications or interior twist-off caps. Formulation requires co-resin to achieve desired properties.

AdapT 231 is a formulated MDEA-based solvent designed for the deep removal of CO₂ from CO₂ containing gas streams.

MP2100 formulations are suitable for 3-piece sanitary ends and bodies for both easy-to-hold and medium-aggressive foods and beverages. Specific formulation needs to be used to achieve desired properties.

Eastman TREVA GC6021 is a cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA™ is a cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman Zendex™ DB-300 agricultural solvent is a non-VOC, high-boiling, nonpolar solvent with good solvency for a wide range of agricultural chemical active ingredients, specifically designed for agricultural formulations.

MDIPA is a clear hygroscopic liquid with an amine-like odor. The freshly distilled product is colorless.

TamiSolve™ NxG-PS is a high-boiling, dipolar aprotic solvent used in pharmaceutical synthesis. TamiSolve NxG-PS has good solvency for a wide range of compounds and a favorable safety profile.

INCI: <I>retinyl sunflowerseedate</I></br>A naturally derived pro-retinol composed of retinol and sunflower fatty acids, Eastman GEM retinyl sunflowerate is a biobased, formulation-stable, easy-to-handle, nonirritating antiaging ingredient. At room temperature, it is a pourable liquid and is supplied as a high-purity (>95%) assay; therefore, it is free of solvent, diluents, and carriers.

Eastman TREVA GC6011 is a cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman Tetrashield™ IC3021 is a protective resin system that provides excellent direct to metal corrosion resistance in weatherable 2K polyurethane industrial coatings. Tetrashield-based coatings can enable reduced labor costs, lower coatings consumption, less environmental impact, and increased productivity. IC3021 provides superior corrosion resistance over iron phosphate pretreated steel, galvanized steel, and smooth cold rolled steel.

Eastman DN500 copolyester is a high flow product designed and engineered for many different applications. With its excellent color and clarity and its ability to mold thick parts with improved gate aesthetics, DN500 is clearly a well-suited copolyester for many applications. Other outstanding features are excellent chemical resistance, high gloss, and improvements in processing such as faster cycle times, and lower scrap rates.

Eastman DN501 copolyester is a high flow product designed and engineered for many different applications. With its excellent color and clarity and its ability to mold thick parts with improved gate aesthetics, DN501 is clearly a well-suited copolyester for many applications. Other outstanding features are excellent chemical resistance, high gloss, and improvements in processing such as faster cycle times, and lower scrap rates. Under existing United States Food and Drug Administration (FDA) regulations, DN501 may be used in food contact articles which comply with the specifications and conditions of use in 21 CFR 177.1240. The product is certified to ANSI/NSF Standard 51.

Marlotherm SH is a high-performance synthetic organic heat transfer medium for use in the liquid phase in closed and forced circulation heat-transfer systems.

Marlotherm LH is a low-viscosity, synthetic organic heat transfer medium for use in both the liquid and vapor phase for closed, forced-circulation heat transfer systems.

Eastman Membrane Material M230 is a high-viscosity, high molecular weight cellulose diacetate. It is supplied as fine, dry, free-flowing powder. The powder is free from coarse particles and excessive fines. Its high purity permits manufacturing of membranes with fewer defects in the separating layer of the membrane, especially for osmotic and gas filtration applications..<P>For applications that require food contact compliance, please refer to Eastman Membrane Material M230, Food Contact.</P>

Eastman Membrane Material M203 is a low viscosity, low molecular weight cellulose diacetate. It is supplied as fine, dry, free-flowing powder. The powder is free from coarse particles and excessive fines. Its high purity permits manufacturing of membranes with fewer defects in the separating layer of the membrane, especially for osmotic and gas filtration applications.<P>For applications that require food contact compliance, please refer to Eastman Membrane Material M203, Food Contact.</P>

Eastman Membrane Material M203, Food Contact is a low viscosity, low molecular weight cellulose diacetate. It is supplied as fine, dry, free-flowing powder. The powder is free from coarse particles and excessive fines. Its high purity permits manufacturing of membranes with fewer defects in the separating layer of the membrane.<P>This product is manufactured, stored, handled, and transported by Eastman under conditions adhering to current Good Manufacturing Practices for food contact applications. This product meets requirements for use in certain food contact applications under regulations of the U.S. Food and Drug Administration (21 CFR), European Commission (Regulation 10/2011) and Switzerland Ordinance of the FDHA on materials and articles intended to come into contact with foodstuffs (817.023.21, Annex 10). Contact your Eastman representative or authorized Eastman distributor for specific regulatory compliance documentation.</P><P>For applications that do not require food contact compliance, please refer to Eastman Membrane Material M203.</P>

Eastman Membrane Material M210, Food Contact is a medium viscosity, medium molecular weight cellulose diacetate. It is supplied as fine, dry, free-flowing powder. The powder is free from coarse particles and excessive fines. Its high purity permits manufacturing of membranes with fewer defects in the separating layer of the membrane.<P>This product is manufactured, stored, handled and transported by Eastman under conditions adhering to current Good Manufacturing Practices for food contact applications. This product meets requirements for use in certain food contact applications under regulations of the U.S. Food and Drug Administration (21 CFR), European Commission (Regulation 10/2011) and Switzerland Ordinance of the FDHA on materials and articles intended to come into contact with foodstuffs (817.023.21, Annex 10). Contact your Eastman representative or authorized Eastman distributor for specific regulatory compliance documentation.</P><P>For applications that do not require food contact compliance, please refer to Eastman Membrane Material M210.</P>

Eastman Membrane Material M230, Food Contact is a high-viscosity, high molecular weight cellulose diacetate. It is supplied as fine, dry, free-flowing powder. The powder is free from coarse particles and excessive fines. Its high purity permits manufacturing of membranes with fewer defects in the separating layer of the membrane.<P>This product is manufactured, stored, handled and transported by Eastman under conditions adhering to current Good Manufacturing Practices for food contact applications. This product meets requirements for use in certain food contact applications under regulations of the U.S. Food and Drug Administration (21 CFR), European Commission (Regulation 10/2011) and Switzerland Ordinance of the FDHA on materials and articles intended to come into contact with foodstuffs (817.023.21, Annex 10). Contact your Eastman representative or authorized Eastman distributor for specific regulatory compliance documentation.</P><P>For applications that do not require food contact compliance, please refer to Eastman Membrane Material M230.</P>

Eastman membrane material M300 is a high-viscosity, high molecular weight cellulose triacetate. It is supplied as dry pellets. Its high purity permits manufacturing of membranes with improved quality control.<P>This product is manufactured, stored, handled and transported by Eastman under conditions adhering to current Good Manufacturing Practices for food contact applications. This product meets requirements for use in certain food contact applications under regulations of the U.S. Food and Drug Administration (21 CFR), European Commission (Regulation 10/2011) and Switzerland Ordinance of the FDHA on materials and articles intended to come into contact with foodstuffs (817.023.21, Annex 10). Contact your Eastman representative or authorized Eastman distributor for specific regulatory compliance documentation.</P><P>For applications that do not require food contact compliance, please refer to Eastman Membrane Material M300.</P>

Eastman Membrane Material M210 is a medium viscosity, medium molecular weight cellulose diacetate. It is supplied as fine, dry, free-flowing powder. The powder is free from coarse particles and excessive fines. Its high purity permits manufacturing of membranes with fewer defects in the separating layer of the membrane, especially for osmotic and gas filtration applications..<P>For applications that require food contact compliance, please refer to Eastman Membrane Material M210, Food Contact.</P>

Eastar™ BR403 copolyester is a water-clear polymer that is great for toothbrush applications. It will not crystallize and thus offers wider processing latitude than conventional crystallizable polyesters while still providing an excellent combination of clarity, toughness, and melt strength.

Eastar™ BR303 copolyester is a brilliantly clear polymer with excellent impact strength, chemical resistance, and low shrinkage, making it a great choice for toothbrush applications.

Zendex™ DB-120 agricultural solvent is a non-VOC, high-boiling, nonpolar solvent. With good solvency for a wide range of chemical active ingredients, it is specifically designed for agriculture formulations. Zendex DB-120 is currently commercial in the United States, Brazil, Belgium, Estonia, France, Germany, Hungary, Ireland, Italy, The Netherlands, Spain, Switzerland, and the United Kingdom.

Eastman Tetrashield™ AC1040 is a durable polyester resin system that improves the performance of automotive clearcoats.

Marlotherm XC is a high performance, wide temperature-range heat transfer fluid for heating and cooling in the most varied fields of applications.

MP2103 formulations are suitable for 3-piece cans and bodies with sanitary or easy-open ends for hard-to-hold (HTH) foods and beverages. Resin provides improved formulation latitude.

Eastman TREVA™ TR6021 is a cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

Eastman TREVA TR6021 is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact.

The world's leading shrink film just got better with the introduction of Eastman Embrace™ Encore to the Eastman Embrace™ family of resins.

Eastman Tritan MXF321 copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321 has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321 has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability. Eastman Tritan MXF321 contains a mold release derived from vegetable based sources.

Eastman Keitex^TM LF1 is an anhydrous (water max. 2.0 m-%) short and medium chain fatty acid blend, containing formic acid which favorably affects the hygienic characteristics of feed and raw materials by reducing a specific microbiological contamination, e.g. <i>Salmonella</i> and other harmful micro-organisms for all animal species.

Eastman Tritan MXF321HF copolyester has been formulated for medical devices and meets UL94 V2 compliance at 1.5 mm. Tritan MXF321HF has passed ISO 10993 testing for cytotoxicity, skin sensitization, and intracutaneous reactivity. Tritan MXF321HF has many outstanding features that include excellent toughness, hydrolytic stability, heat resistance, chemical resistance, and melt flowability to fill complex parts. Tritan MXF321HF contains a mold release derived from vegetable-based sources.

Eastman Tritan™ Renew TX1001-25 is an amorphous copolyester with excellent appearance and clarity. Tritan Renew TX1001-25 contains a mold release derived from vegetable based sources. This product's most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new-generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Combined with Tritan's outstanding chemical resistance and hydrolytic stability, these features give molded products enhanced durability in the dishwasher environment, which can expose products to high heat, humidity and aggressive cleaning detergents. Tritan Renew TX1001-25 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. Tritan Renew TX1001-25 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman Tritan™ Renew TX2001-25 is an amorphous copolyester with excellent appearance and clarity. Tritan Renew TX2001-25 contains a mold release derived from vegetable based sources. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new-generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Tritan Renew TX2001-25 is certified to NSF/ANSI Standard 51 for Food Equipment Materials.

Eastman Tetrashield™ PW5100 is a high-performance resin system designed for powder coating applications. Tetrashield protective resin systems are designed to enhance coating performance for architectural powder and protective coatings.

Eastman Eastek™ 5545 polymer is a high-performance polyester resin for polyurethane hot melt electronic adhesives. Eastman Eastek 5545 polymer is featured with reduced viscosity, increased Tg, and improved formulation compatibility to enable greater productivity, application consistency, long-term durability, and design flexibility in multi-substrate electronic bonding applications.

Eastman Eastek™ 4500 polymer is a high-performance polyester resin for polyurethane hot melt adhesive applications. Eastman Eastek 4500 polymer is designed to reduce viscosity, increase Tg, enhance UV resistance, and improve formulation compatibility to enable greater productivity, application consistency, and long-term durability of the bonded structure.

<i>Meets ISO 10993 and/or USP Class VI biocompatibility requirement</i><BR>Eastar™ copolyester MN021 Natural is a thermoplastic condensation copolymer produced by a continuous melt-phase polymerization process followed by a solid-state polymerization process. It has a relatively high flex modulus and yield strength. This product does not contain a mold release.

Skydrol 5 offers higher temperature capability than Type IV fluids, the lowest density, and better paint compatibility.

Skydrol™ 500B-4 is the most worker friendly of the aviation phosphate esters; it is least irritating to skin and less prone to form mists which can be irritating to the respiratory tract .

Skydrol LD-4 features low density, excellent thermal stability, valve erosion prevention, and deposit control.

Skydrol PE-5 was developed to meet and exceed the more demanding Type V fluid requirements. It features the longest fluid life of any commercially available fluid, low density and low viscosity at low temperature.

Eastman Propcorn Feed LP4 NC has a strong anti- mold effect in the compound feeds and raw materials and helps to prevent formation of mycotoxins during storage

Eastman 168™ Renew 20 non-phthalate plasticizer performs as good as or better than most ortho-phthalate plasticizers. In general-purpose plasticizer applications, it offers good performance properties, excellent low-temperature flexibility, resistance to extraction by soapy water, and excellent nonmigration properties. Eastman Renew plasticizers have been certified by International Sustainability & Carbon Certification (ISCC), a global, independent agency that tracks sustainable content in a variety of industries. Renew plasticizers are produced with ISCC-certified circular content by mass balance allocation.

Eastar™ Renew copolyester 6763-50 meets ISO 10993 and/or USP Class VI biocompatibility requirement.

Eastman Acitra^TM LH1 preserves compound feeds and raw materials and prevents recontamination with microorganisms.

Eastman DOA Renew 20 plasticizer (bis(2-ethylhexyl) adipate) is a light-colored, oily liquid generally used as a plasticizer for PVC. It features flexibility at low temperatures, good electrical properties, resistance to weathering, and heat stability. Eastman Renew plasticizers have been certified by International Sustainability & Carbon Certification (ISCC), a global, independent agency that tracks sustainable content in a variety of industries. Renew plasticizers are produced with ISCC-certified circular content by mass balance allocation.

Eastar™ Renew copolyester AN014-50 Natural is a high flow product that contains a mold release.

Eastar™ Renew GN071-100 copolyester is a sustainable, clear copolyester used in a variety of packaging and consumer product applications, including food and beverage packaging, general-purpose packaging, flexible film packaging, and consumer products.

Eastman Cristal™ One Renew-100 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough, exhibits good chemical resistance and contains 100% certified recycled content*. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ Renew CN015-50 Natural copolyester is a high flow product that contains a mold release to provide ease of demolding.

Eastman Cristal™ One Pro Renew-100 is a copolyester designed to be fully compatible with the PET recycling stream.

Eastman Keitex BC is a blend of organic acids that preserves and acidifies complete swine feed and complete poultry feed and prevents recontamination with micro-organisms.

Eastman DOA Renew 20 plasticizer (Bis(2-Ethylhexyl) Adipate), Kosher is a light colored, oily liquid generally used as a plasticizer for PVC. Eastman DOA Renew 20 plasticizer is used to produce clear films for food packaging applications.

Eastman Eastar™ Renew DN501-50 copolyester is a high flow product designed and engineered for many different applications. With its excellent color and clarity and its ability to mold thick parts with improved gate aesthetics, Eastar™ Renew DN501-50 is clearly a well-suited copolyester for many applications. Other outstanding features are excellent chemical resistance, high gloss, and improvements in processing such as faster cycle times, and lower scrap rates. Eastar™ Renew DN501-50 is also ideally suited for two-shot molding due to its lower processing temperatures, very slow crystallization rate, and flow characteristics. Eastar™ Renew DN501-50 contains a mold release derived from vegetable based sources.

Eastman Tetrashield™ protective resin MP2303 formulations are suitable for 3-piece cans and bodies with sanitary or easy-open ends for hard-to-hold (HTH) foods and beverages. MP2303 provides improved formulation latitude.

Eastman Cristal™ One Renew-30 is a copolyester designed to be fully compatible with the PET recycling stream. Thus, it enables brand owners to achieve recyclable cosmetics packaging that is tough, exhibits good chemical resistance. It is suitable for molding thick-walled transparent containers or parts (up to 9mm thickness), while maintaining clarity and color. For ISBM applications, Cristal™ One is recommended for thicker luxury bottles with complex shapes.

Eastman Cristal™ One Pro Renew-30 is a copolyester designed to be fully compatible with the PET recycling stream.

AIV^® Via is a premixture of silage additives for several feed ensiling purposes where risks are related to porosity of ensiled material as well as moisture range favoring molds.

SkyKleen 1000 is an aviation solvent that combines excellent cleaning performance with environmentally friendly characteristics.